Stimulation Level Adjustment Button
“
” and “
”
to adjust the stimulation output. Press
to increase and
to decrease. The Maximum level is 10.
The ON/OFF Button
Hold the button for 2 seconds to turn it on. The LED indicator turn Blue then off, and the LCD should show
default “A01. To
switch the power off, hold this button for 2 seconds and the power light indicator will switch off.
Beep/Tone Button
“
”
Press the button, the collar will emit a no- stimulation Beep.
Vibration Button
“
”
Press once for a single short vibration. Press and hold the button for a continuous vibration for max. 8 seconds.
“
”
Press once for a single short static correction with pre-set output. Press and hold the button for a continuous static
correction for max. 8 seconds.
The Dog Selector Buttons
The Transmitter is able to train up to 3 dogs up to 800 metres line of sight. The default is in
“1”
. The LCD screen will display dog
ID “
A XX
”.
Press
“2”
button to switch to dog
2
. The LCD will display “
BXX
”.
Press
3
to switch to dog
3
. And the LCD will display
“
C XX
”.
A = Dog 1; B = Dog 2; C = Dog 3;
“XX” = The
output level for static correction & vibration.
Please Note:
The LED flashes Red when the battery is low.
The Barkmate Training remote is able to control up to 3 collars. You may need to unpair the collar before you can pair it with the
new remote as the collar may be paired with a different remote for testing purpose from the factory.
MAKE SURE the collar is in
dog training mode (flashes GREEN once every 5 seconds).
Unpairing the new collar/remove coding
1.
Turn both collar (wish to unpair) and remote transmitter on. (if you have more than one collar, please turn off other
collars). Keep the collar close to transmitter (almost touches or touches each other).
2.
Press & hold both
“
”
and “
” button
on the remote in the same time, until the digit on the LCD changes very fast.
3.
Press any dog selector button (
“
1
”
,
“
2
” or “
3
”). Once
you press the button, the collar should beep five times rapidly. If
the collar doesn’t beep, release the button and press/hold the button (“
1
”
,
“
2
” or “
3
”)
again.
If you want to remove an existing collar from a number, you can press and hold the number of dog selector button until
the collar beeps five times and flashes Green Rapidly.
4.
Press & hold both
“
”
and the “
” button
again until the digit on the LCD display stop changing. The collar is
unpaired (coding removed) from previous transmitter successfully.
Dog collar should still flash Green rapidly
.
Pair the new collar to the remote
1.
Turn both collar (wish to pair) and remote transmitter on (Collar in Dog Training Mode).
2.
Press & hold the “
”button and “
” button at the same time, u
ntil the digit on the LCD display changes very fast. It
means the remote transmitter is enter the pairing mode. The LED on dog collar should flash quickly in the same time.
5.
Press & hold on the Dog selection button:
Press and hold “
1
” to match the
Receiver Collar as the dog 1, press and hold
“
2
” to match the Receiver Collar as
dog 2, or press and hold
“
3
” to match the collar as the dog
3. The collar should
“beep”
5 times rapidly and green LED on the collar will flash normally(
GREEN once every 5 seconds)
. If the collar does
n’t
beep, release the button and press/hold the button again.
3.
Release the Dog Selector button.
4.
Press &
hold the “
” button and the “
” button at the same time again, until the digit
on LCD display is no longer
changing, then release both buttons.
5.
Select the collar number and test with warning beep or vibration
Transmitter Charging
