Barefoot Sound MicroMain 27 Gen2 Owner'S Manual Download Page 15

 

 

14 

14. Warranty 

 
This product is under limited warranty as described in the following conditions. The warranty period commences 
on the date of purchase from the authorized dealer.  Barefoot Sound reserves the right to request your original 
purchase receipt as proof of the date of purchase.  The warranty follows the product and is transferable to any 
subsequent owner(s) as long as a copy of the original purchase receipt from the authorized dealer can be 
provided. 
 
Electronic components and cabinetry of the product are warranted for a period of three (3) years against 
manufacturing defect, covering parts and labor for necessary repairs. 
 
Moving speaker components are warranted for a period of one (1) year against manufacturing defect. 
 
The manufacturer’s warranties are limited to physical defects in the materials, parts and workmanship used in 
making the product. Misuse, incorrect installation, connection or handling, repairs or modifications performed by 
unauthorized persons, abnormal conditions, deliberate abuse, damage due to accidents such as power surges, 
water, fire, or any other are excluded from any warranty claims. In addition, faulty or unsuitable ancillary 
equipment, accessories, or options are fitted at owner’s risk. 
 
Barefoot Sound warrants all service repairs and replacements for 180 days from the date of return to the 
customer/owner. This warranty specifically excludes unrelated additional defects or failures. Otherwise the same 
general provisions of the limited product warranties apply. 
 

Technical Support and Service

 

 
For warranty service and assistance, contact the original authorized dealer/distributor to arrange for return and/
or repair of the product.  Barefoot Sound will strive to satisfy all service requests in the fastest manner possible. 
Under the warranty, Barefoot Sound will repair, or at its discretion, replace the product at no charge, provided it 
is returned (postage paid) to an authorized Barefoot Sound service center.  Any shipping or duties incurred are 
the customer’s responsibility. Products should be returned suitably packaged to protect from shipping damage, 
or in their original packaging.  Barefoot Sound shall be the sole and final authority to determine the validity of all 
warranty issues.  All non-warranty repairs for current products will be charged according to the service repair 
pricing schedule. Repair prices will either be based on a flat fee for repair or replacement, or will be estimated 
depending on the repair deemed necessary. 

Summary of Contents for MicroMain 27 Gen2



















Reviews: