barebones Outfitter Safari Tent Manual Download

Page: 18 / 20

STEP 14: PLACE HEAT MAT AND FINISH STOVE ASSMEBLY

• Place Heat Mat.

• Complete Assembly

Use Heat Mat

Use Spark Arrestor

• Use provided Heat Mat to prevent floor damage.

• Position stove to the back of the Heat Mat as shown.

• Spark Arrestor must be placed over stove pipe to prevent embers from damaging roof.

Important!

Stove Use Warning!

• Carbon Monoxide can be deadly, we highly recommend using a Carbon Monoxide Alarm if using a stove.

• Never use stove without opening multiple vents or windows.

• Never leave stove in use, unattended.

• Keep children away from hot surfaces.

• Stove is intended for heat not cooking.

• Poles and joints surrounding stove may become hot.

• Always use Spart Arrestor on stove pipe

• Maintain 2' clearance around stove at all times

Ventilation

• We recommend opening both top vents at least 1/2 way for proper ventilation.

*Please refer to the stove manufacturers guide for additional information.

Summary of Contents for Outfitter Safari Tent





















Search results

Summary of Contents for Outfitter Safari Tent

Reviews:

Related manuals for Outfitter Safari Tent

Brands by name

Popular brands

barebones Outfitter Safari Tent, Manual

Search results

Summary of Contents for Outfitter Safari Tent

Reviews:

Related manuals for Outfitter Safari Tent

Brands by name

Popular brands