background image

Manual

2100-319F

Page

3 of 10

Getting Other Information and Publications

These  publications can  help you install  the air
conditioner or heat pump. You can usually find these at
your local library or purchase them directly from the
publisher. Be sure to consult current edition of each
standard.

Standard for the Installation of ........... ANSI/NFPA 90A
Air Conditioning and
Ventilating Systems

Standard for Warm Air Heating ......... ANSI/NFPA 90B
Air Conditioning Systems

QT

EC

 Installation Instruction Manual ..... Bard/2100-288

FOR MORE INFORMATION, CONTACT THESE
PUBLISHERS:

ACCA

Air Conditioning Contractors of America

1712 New Hampshire Avenue, NW
Washington, DC 20009
Telephone: (202) 483-9370
Fax: (202) 234-4721

ANSI

American National Standards Institute

11 West Street, 13th Floor
New York, NY 10036
Telephone: (212) 642-4900
Fax: (212) 302-1286

ASHRAE American Society of Heating, Refrigerating

& Air Conditioning Engineers, Inc.

1791 Tullie Circle, N.E.
Atlanta, GA 30329-2305
Telephone: (404) 636-8400
Fax: (404) 321-5478

BARD

Bard Manufacturing Company

1914 Randolph Drive
Bryan, OH  43506
Telephone:  (419) 636-1194
Fax:  (419) 636-2640

Summary of Contents for QWS48A QWS48A-16











Reviews: