Manual 2100-677B
Page
2 of 2
Execute a run test on each unit to verify the equipment is
functioning correctly (TEC-EYE)
1. Use UP or DOWN keys to scroll to
Run Test A11
(MULTI-TEC units) or
Run Test A10
(WR Series units).
2. Press ENTER key to scroll to
Run Test Enable
parameter.
3. Use UP or DOWN key to change value to
ON
. The run
test will begin.
See Installation Instructions 2100-676 if additional
information on run testing units is needed.
Clear unit alarm logs (TEC-EYE)
To clear the wall-mount unit alarm logs:
1. Press MENU key to go to the Main Menu screen.
2. Use UP or DOWN keys and ENTER key to enter
password 1313.
3. Press UP or DOWN keys to scroll to
Settings
; press
ENTER key.
4. Press UP or DOWN keys to scroll to
Initialization
; press
ENTER key.
5. Press ENTER key to scroll to
Delete Alarm Logs?
(MULTI-TEC units) or
Clear Alarm Logs?
(WR Series).
6. Press UP or DOWN key to value to
YES
; press ENTER key.
After first unit has been set up and configured, follow the
above steps to set up and configure the remaining units.
Set LC Controller Timezone and Date/Time
(LC Controller)
1. Press MENU key to access the Main Menu screen.
2. Use UP or DOWN keys and ENTER key to enter
password 1313.
3. Press the UP or DOWN keys to scroll to the
Settings
menu; press ENTER key.
4. Press UP or DOWN keys to scroll to
Date/Time
menu;
press ENTER key.
5. Press ENTER key to scroll to the desired value to be
changed.
6. Press UP or DOWN keys to change the value.
7. Press ENTER key to save.
8. Press the ESCAPE key several times to return to Main
Menu screen.
Configure sensors (LC Controller)
The LC is capable of utilizing four temperature sensors and
three humidity sensors. The controller must be configured
to match the sensors for the shelter. The available sensors
are Zone 1 Indoor Humidity, Zone 2 Indoor Humidity, Zone
3 Indoor Humidity, Zone 1 Indoor Temperature, Zone 1
Remote Temperature, Zone 2 Remote Temperature and Zone
3 Remote Temperature.
The Zone 1 Indoor Humidity and Zone 1 Indoor Temperature
sensors are enabled by default. The additional indoor humidity
and indoor temperature sensors are disabled by default.
See Installation Instructions 2100-676 if information is
needed on configuring (enabling/disabling) sensors.
If necessary, the sensors can be calibrated at this time too. For
information on calibrating the sensors, see manual 2100-676.
See LC6000 Service Instructions manual 2100-669 for
information on setting up the smoke, hydrogen and generator
relays (if applicable).
Enter total number of units (LC Controller)
1. Press MENU key to go to the Main Menu screen.
2. Use UP or DOWN keys and ENTER key to enter
password 1313.
3. Press UP or DOWN keys to scroll to
Sys Config
; press
ENTER key.
4. Press UP or DOWN keys to scroll to
General
; press
ENTER key.
5. Press ENTER key to scroll to
Total Units
.
6. Press UP or DOWN keys to adjust value to correct
number of units.
7. Press ENTER key to save.
Verify units are online (LC Controller)
Once a unit is uniquely addressed, communication can be
verified at the LC controller.
With the correct number of units set at the LC controller,
each unit can be remotely viewed from the LC controller
Information screens.
To view these screens:
1. Press
ESCAPE key to view the Status screen. (May need
to be pressed more than once.)
2. Press UP or DOWN key until the Quick Menu in the
lower right corner of the screen displays the Information
icon ( ); press ENTER key.
3. Press UP or DOWN keys to scroll through the Information
screens until the desired unit Information screen appears.
In addition to being able to remotely view the units, an
alarm will be generated on the LC controller for units not
communicating.
Clear controller alarm logs (LC Controller)
To clear the LC controller alarm logs:
1. Press MENU key to go to the Main Menu screen.
2. Use UP or DOWN keys and ENTER key to enter
password 1313.
3. Press UP or DOWN keys to scroll to
Settings
; press
ENTER key.
4. Press UP or DOWN keys to scroll to
Initialization
; press
ENTER key.
5. Press ENTER key to scroll to
Delete Alarm Logs?
6. Press UP or DOWN key to value to
YES
; press ENTER key.
7. Press ESCAPE key several times to return to Main Menu
screen.
Once all the installation steps have been completed, all
alarms and alarm logs have been cleared and system
verification and run test results were satisfactory, the
installation can now be considered “complete”.
