Bard BrightStat  8403-081 Installation And Application Instructions Download Page 14

Manual 2100-680 

Page 

14 of 18

Example of Non-Recommended Deployment 

The illustration below shows four room controllers (two 
for each room) installed in non-ideal locations for the 
two rooms.
The examination room shows one room controller 
installed in a low traffic area near the door, and a 
second room controller installed on the wall directly 
opposite the door. For the room controller installed 
in the corner wall, the PIR could be blocked by the 
opened door, while occupant traffic could also be 
minimal in this area of the room. For the second room 
controller installed opposite the door, the PIR detection 
could fall outside the specified detection zone, while 
at the same time most occupant movement would not 
be lateral to the PIR, thereby not respecting optimal 
crossing patterns for PIR detection. 

Non-Recommended Installation

The waiting room shows one room controller installed 
in the corner of the room, and a second room controller 
installed beside the reception area. For the room 
controller installed in the corner, the opening/closing of 
the door creates high probability that the PIR would get 
blocked, and therefore, occupancy going undetected. 
For the room controller installed beside the reception 
area, occupant traffic could fall outside the detection 
zone, and the receptionist would often be below the 
5' recommended installation height for the room 
controller. 

Examination Room

Waiting Room

Summary of Contents for BrightStat 8403-081



















Reviews: