![background image](http://html.mh-extra.com/html/barco/zeus/zeus_installation-and-safety-manual_474408013.webp)
2. Safety
To prevent personal injury
•
Leave an exclusion zone around all external surfaces of the projector. See "Safety training to be provided by the installer", page
7.
•
Isolate electrically before replacing the lamp or lamp house. Caution: hot lamp (house).
•
Caution: high pressure lamp may explode if improperly handled. Refer servicing to quali
fi
ed service personnel.
•
To prevent injury and physical damage, always read this manual and all labels on the system before inserting the lamp casing,
connecting to the wall outlet or adjusting the projector.
•
To prevent injury, take note of the weight of the projector. Minimum 4 adult persons are needed to carry the projector.
•
To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.
•
Warning: high intensity light beam. NEVER look into the lens! High luminance could result in damage to the eye.
•
Warning: extremely high brightness lamps
: this projector uses extremely high brightness lamps. Never attempt to look
directly into the lens or at the lamp. Avoid close range re
fl
ection of the projected image on any re
fl
ecting surface (such as glass,
metal, …). Take into account the light beam Hazard Distance (HD) and never enter the Restriction Zone (RZ), as de
fi
ned in
chapter "Light beam Hazard Distance (HD)", page 12).
•
Before attempting to remove any of the projector’s covers, disconnect the projector mains terminals for removal of all power
from the projector.
•
When required to remove all power from the projector, to access parts inside, always disconnect the projector mains terminals.
•
Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and
possible injury to the user.
•
It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall be changed if they have become
visibly damaged to such an extent that their effectiveness is impaired. For example by cracks or deep scratches.
•
Warning: protection from ultraviolet radiation
: do not look directly in the light beam. The lamp contained in this product is
an intense source of light and heat. One component of the light emitted from this lamp is ultraviolet light. Potential eye and skin
hazards are present when the lamp is energized due to ultraviolet radiation. Avoid unnecessary exposure. Protect yourself and
your employees by making them aware of the hazards and how to protect themselves. Protecting the skin can be accomplished
by wearing tightly woven garments and gloves. Protecting the eyes from UV can be accomplished by wearing safety glasses
that are designed to provide UV protection. In addition to the UV, the visible light from the lamp is intense and should also be
considered when choosing protective eye wear.
•
Exposure to UV radiation
: some medications are known to make individuals extra sensitive to UV radiation. The American
Conference of Governmental Industrial Hygienists (ACGIH) recommends occupational UV exposure for an-8 hour day to be
less than 0,1 micro-watts per square centimeters of effective UV radiation. An evaluation of the workplace is advised to assure
employees are not exposed to cumulative radiation levels exceeding these government guidelines. The exposer of this UV
radiation is allowed for only 1 hour per day for maintenance and service personnel.
•
When the projector is mounted above persons, a lens safety cable should always be mounted.
•
The exhaust output on top of the projector must be coupled to an external exhaust system. In case the projector is equipped
with an exhaust output at the rear then there is no need for an external exhaust system.
W
ARNING
:
Never look into the exhaust output on the top of the projector. High luminance and UV radiation
could result in damage to the eye. The installation of an exhaust system on top of the projector is mandatory
before operating the projector.
W
ARNING
:
The exhaust output of the projector is very hot when the projector is on. To avoid burns, let the
projector cool down for at least 15 minutes before touching the exhaust output.
To prevent
fi
re hazard
•
Leave an exclusion zone around all external surfaces of the projector. See "Safety training to be provided by the installer", page
7.
•
Do not cover the projector or the lens with any material while the projector is in operation.
•
Keep
fl
ammable and combustible materials away from the projector at all times.
•
Mount the projector in a well ventilated area away from sources of ignition and out of direct sun light.
•
In the event of
fi
re use sand, CO
2
or dry powder
fi
re extinguishers. Never use water on an electrical
fi
re.
•
Heat sensitive materials should not be placed in the path of the exhausted air or on the lamp house.
•
Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect
it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the
projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat
register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
•
Projection rooms must be well ventilated or cooled in order to avoid build up of heat. It is necessary to vent hot exhaust air from
console to the outside of the building. The mandatory exhaust system must include a blower that maintain at least 4m
3
/min
(140 CFM) when measured at the projector exhaust opening.
•
Let the projector cool down completely before storing. Remove cord from the projector when storing.
•
Heat sensitive materials should not be placed in the path of the exhausted air or on the lamp house.
R5905961 ZEUS 09/03/2015
9
Summary of Contents for ZEUS
