Barco SP4K-B, Safety Manual

Page: 4 / 14

R5912127 /03 SP4K-B 4
Why a restricted access location: This is a RG3 product. Based on international requirements, no person is allowed to enter the projected
beam within the zone between the projection lens and the related Hazard Distance (HD). This shall be physically impossible by creating
sufficient separation height or by placing optional barriers. Within the restricted area operator training is considered sufficient. The
applicable separation heights are discussed in
“ High Brightness precautions: Hazard Distance ” , page 8 .
Users definition
Throughout this manual, the terms SERVICE PERSONNEL and TRAINED PROJECTIONIST refers to persons having appropriate
technical training and experience necessary to be knowledgeable of potential hazards to which they are exposed (including, but not
limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task,
and of measures to minimize the potential risk to themselves or other persons. The term USER and OPERATOR refers to any person
other than SERVICE PERSONNEL or TRAINED PROJECTIONISTS, AUTHORIZED to operate professional projection systems.
The TRAINED PROJECTIONISTS may only perform the maintenance task described in the User & Installation manual. All other
maintenance tasks and service tasks must be performed by qualified SERVICE PERSONNEL.
The DLP Cinema Systems are intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL familiar with potential
hazards associated with high voltage, high intensity light beams generated by lasers. Only qualified SERVICE PERSONNEL and
TRAINED PROJECTIONISTS, knowledgeable of such risks, are allowed to perform service functions inside the product enclosure.
1.2 Important safety instructions
To prevent the risk of electrical shock
• This projector should be operated from an AC power source. Ensure that the mains voltage and capacity matches the projector
electrical ratings. If you are unable to install the AC power requirements, contact your electrician. Do not defeat the purpose of the
grounding.
• Installation should be done according to the local electrical code and regulations by qualified technical personnel only.
• This product is equipped with a 5-terminal barrier strip for the connection of a power line. The projector can run on one of the following
configurations, depending on what power system is available:
-
A 3W+N+PE power system (Y configuration).
- A 3W+PE power system (Δ configuration).
- A mono phase system with power line with a separate earth ground PE.
If you are unable to install the AC power requirements, contact your electrician. Do not defeat the purpose of the grounding.
• This product is equipped with a 2-terminal barrier strip for the connection of a UPS power cord (2-pole, 3-wire grounding).
• The electronics of the projector (UPS INLET) must be powered from a suitable UPS unit. The building has to be provided with a circuit
breaker of max 16A to protect the UPS.
• The building installation has to be provided with a circuit breaker of max 40A to protect the complete unit.
• The circuit breakers are considered as readily accessible disconnect devices that must be incorporated externally to the equipment for
removal of the power to the projector mains terminals and UPS inlet terminals.
• The cross-sectional area of the conductors in the power supply cord should be not less than 4 mm² (10 AWG) while using a circuit
breaker of 40A max. The power cord should have a rating depending on what power system is available:
-
Y configuration: min 500V.
- Δ configuration: min 300V.
- Mono phase configuration: min 300V.
• The cross-sectional area of the UPS inlet cord shall be not less than 1.5 mm² (14 AWG) and has a rating of minimum 300V.
• In case of using a circuit breaker of a current rating less than 40A, the cross-sectional area of the conductors in the power supply cord
must comply with the local electrical code regulations where the projector is installed.
• The cable gland of the power supply cord has a clamping range between 11 mm and 21 mm ( cable diameter of the power supply cord
must be in this range :11-21 mm)
• Disconnect the power to the projector mains terminals for removal of all power from the projector.
• Do not allow anything to rest on the power cord. Do not locate this projector where persons will walk on the cord.
• Do not operate the projector with a damaged cord or if the projector has been dropped or damaged - until it has been examined and
approved for operation by a qualified service technician.
• Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
• If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated for less
amperage than the projector may overheat.
• Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short circuit
parts that could result in a risk of fire or electrical shock.
• Do not expose this projector to rain or moisture.
• Do not immerse or expose this projector in water or other liquids.
• Do not spill liquid of any kind on this projector.
• Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before
resuming operations.
• Do not disassemble this projector, always take it to an trained service person when service or repair work is required.
• Do not use an accessory attachment which is not recommended by the manufacturer.
• Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long
periods of time, remove all power from the projector. This will prevent damage to the projector due to lightning and AC power-line
surges.
To prevent personal injury
• To prevent injury and physical damage, always read this manual and all labels on the system before powering the projector or
adjusting the projector.
• Do not underestimate the weight of the projector. The projector weighs ±155 kg ( ±342 lbs), for SP4K-55B weight is 175 kg (±385 lbs).
To prevent personal injury a hoisting tool should be used to lift the projector.
Safety