![background image](http://html1.mh-extra.com/html/barco/sp2k-c/sp2k-c_installation-manual_4254082084.webp)
R5914712 /00
SP2K-C
84
7.8 ICMP-X configuration via Web Communicator
About ICMP-X configuration
The following parameters are available to configure the ICMP-X:
•
Global settings
: allows defining name of the ICMP-X, host name (network identifier) and IP address which
can be used for communication with external content devices.
•
User settings
: definition of all users allowed on the ICMP-X.
•
Server settings
: definition of access to servers and storage libraries of content (movies, KDM, etc.).
•
Player settings
: Audio delay and audio output frequency.
•
Audio channel
: allows defining the mapping of audio channels (content) on each audio output (AES
outputs of the ICMP).
•
Scheduler setting
: Enable/Disable scheduler at startup, delays allowed in scheduler mode and length of
schedule history.
•
Devices
: allows defining communication ports settings, to access external devices controlled by the
automation.
•
Automation Cues
: event cues that are triggered from different sources and to which can be assigned
actions to be executed by the automation engine.
•
Verify internal clock of the ICMP-X.
All installation and maintenance operations on the ICMP-X are performed via Web Communicator,
the Barco configuration software. Please refer to the user guide for more information.
Factory settings
Restoring to factory setting is a feature that removes all settings performed on the ICMP-X and replaces them
with the default values set at the factory. Please refer to the user guide for more information.
Internal clock settings
The crystal on the ICMP-X board that manages the clock shows a minimal drift. This is expected behavior, all
clock crystals have an unavoidable drift. The internal clock can be corrected using the Web Communicator.
Checking the
internal clock settings
and correcting if necessary is a maintenance action should be repeated
every 3 months. When neglected and the drift becomes too big, the system may lock up.
However, it is also possible to do an automatic correction by enabling
Automatic Synchronization
in Web
Communicator. When enabled, you have to enter the IP address for a Network Time Protocol server (NTP
server) where the ICMP-X can find a proper sync signal. As long as the projector is connected to an NTP
server, the ICMP-X will automatically keep its clock correct. For detailed instructions see user guide.
Summary of Contents for SP2K-C
