Barco SIM 7C R9011206 Service Manual Download Page 19 | Manualshive

Page: 19 / 44

background image

4. Covers

How to install the lens cover bottom?

1. Put the lens cover bottom in the right position

2. Fix the lens cover top by tightening the three

fi

xing screws

Image 4-6
Lens cover bottom:

fi

xing screws on the front side of the projector

4.3

Top

fi

lter cover

Overview

•

Removing the top

•

Installing the top

Description

The

top

fi

lter cover

is used to

fi

x the top dust

fi

lter in its housing.

4.3.1

Removing the top

fi

lter cover

Necessary tools

Torx screwdriver T10

How to remove the top

fi

lter cover?

1. Release the 4

fi

xing screws

Tip:

The screws are no-loss screws and will not drop.

Image 4-7
Top

fi

lter cover:

fi

xing screws

2. Lift the top

fi

lter cover to remove it

R59770119 SIM 7C 28/05/2008

15

«
...
17
18
19
20
21
...
»

Summary of Contents for SIM 7C R9011206













































Reviews:

No comments

Related manuals for SIM 7C R9011206

CREE LIGHTING DOT Series

Brand: IDEAL INDUSTRIES Pages: 2

Brand: Panasonic Pages: 132

PTL711XU - LCD PROJECTOR

Brand: Panasonic Pages: 38

Brand: Eiki Pages: 1

Brand: PNI Pages: 158

PJD6251 - XGA DLP Network Projector

Brand: ViewSonic Pages: 2

Brand: UTEPO Pages: 2

COMPACTVIEW CLAN X15-I

Brand: 3D Perception Pages: 36

Brand: Taiden Pages: 71

Brand: Eaton Pages: 2

Brand: Mitsubishi Pages: 79

Brand: artograph Pages: 24

L-com SRCN-C266

Brand: Infinite Pages: 3

Ritzscreen V540

Brand: Verano Pages: 12

Brand: NEC Pages: 82

Brand: NEC Pages: 37

Brand: NEC Pages: 10

Brand: NEC Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands