Barco RLM W Series Reference Manual Download Page 100

Page: 100 / 151

9. Color alignment

9.2

Custom color space

What can be done ?

The user can change the shape of the color gamut by changing the corner coordinates of the red, green
and blue corner point. The changes are limited within a certain area.

The coordinates of the white point can be changed in the same way to obtain a custom white point.

How to adjust

1. Click on the up down control of the spin box to change the X or Y coordinate of the selected color.

Or,
click in the input

eld, select the current value and enter a new value with the keyboard. (image 9-2)

Image 9-2
Custom color gamut adjustment

Native color gamut

Custom color gamut

Native white point

Custom white point

R59770513 RLM W-SERIES 28/07/2010

Summary of Contents for RLM W Series
























































































































































Search results

Summary of Contents for RLM W Series

Reviews:

Brands by name

Popular brands

Barco RLM W Series, Reference Manual

Search results

Summary of Contents for RLM W Series

Reviews:

Brands by name

Popular brands