![background image](http://html1.mh-extra.com/html/barco/r92112011/r92112011_user-manual_4242641015.webp)
3. Installation guidelines
3. INSTALLATION GUIDELINES
Overview
•
•
3.1
Safety warnings
W
ARNING
:
Before installing the projector,
fi
rst read the safety instructions in the safety manual (R5975258)
delivered with the projector.
Insure that the room can be easily evacuated in case of a lamp explosion.
Mercury vapor warnings
Keep the following warnings in mind when using the projector. The lamp used in the projector contains mercury. In case of a lamp
rupture or lamp explosion there will be a mercury vapor emission. In order to minimize the potential risk of inhaling mercury vapors:
•
Insure the projector is installed in ventilated rooms only.
•
Replace the lamp module before the end of its operational life.
•
Promptly ventilate the room after a lamp rupture or lamp explosion has occurred and evacuate the room (particularly in case of
a pregnant woman).
•
Seek medical attention if unusual health conditions occur after a lamp rupture or lamp explosion, such as headache, fatigue,
shortness of breath, chest-tightening coughing or nausea.
3.2
Installation guidelines
General conditions
Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to
the optimum use of the projection system.
Temperature conditions
Temperature range during operation
•
Min. ambient temperature : 0 °C or 32 °F
•
Max. ambient temperature : 40 °C or 104 °F
The projector will not operate if ambient air temperature falls outside this range (0°C- 40°C or 32°F-104°F).
Temperature range in non-operation condition
•
Min. ambient temperature : -10 °C or 14 °F
•
Max. ambient temperature : 60 °C or 140 °F
Humidity conditions
Operation: 0 to 90 % RH non-condensing
Storage: 0 to 90 % RH non-condensing. Recommended RH = 50%
Environment
Do not install the projection system in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight,
excessive dust or humidity. Be aware that room heat rises to the ceiling; check that temperature near the installation site is not
excessive.
Environment condition check
A projector must always be mounted in a manner which ensures the free
fl
ow of clean air into the projectors ventilation inlets as well
as free
fl
ow at the ventilation outlets. The installation must also allow easy access to the consumable parts (dust
fi
lters, lamps, etc.)
For installations in environments where the projector is subject to airborne contaminants such as that produced by smoke machines
R59770066 SIM 7Q SERIES 08/12/2014
11
Summary of Contents for R92112011
