background image

• Read the safety and
operating instructions before
operating the apparatus.
• Retain safety and operating
instructions for future
reference.
• Adhere to all warnings on
the apparatus and in the
operating instructions
manual.
• Follow all instructions for
operation and use.

•This apparatus conforms to:

CE, IEC 60950, UL 60950, CAN/
CSA C22.2 No. 60950 (cUL)

• FCC notice
This equipment has been
tested and found to comply
with the limits of a class A
digital device, pursuant to
Part 15 of the FCC rules.
These limits are designed to
provide reasonable
protection against harmful
interference when the
equipment is operated in a
commercial environment.
This equipment generates,
uses and can radiate radio
frequency energy and, if not
installed and used in
accordance with the
instruction manual, may
cause harmful interference
to radio communications.

Operation of this equipment
in a residential area is likely
to cause harmful
interference in which case
the user will be required to
correct the interference at
his own expense.

 Power connection

•  Warning: This apparatus
must be earthed!
• Power requirements: The
apparatus must be powered
using the 12 VDC power
supply that is supplied with
the apparatus.
The 12 VDC power supply
must be powered by the AC
mains voltage.
• Do not overload wall outlets
and extension cords as this
may result in fire or electric
shock.
• Mains lead protection (U.S.:
Power cord): Supply cords
should be routed so that they
are not likely to be walked
upon or pinched by items
placed upon or against them,
paying particular attention to
cords at plugs and
receptacles.

Water and moisture
• Never expose the
apparatus to rain or moisture.
• Never use the apparatus
near water - e.g. near a
bathtub, washbasin,
swimming pool, kitchen sink,
laundry tub or in a wet
basement.

Ventilation
• Do not cover or block the
ventilation openings in the
cover of the set. When
installing the apparatus in a
cupboard or another closed
location, heed the necessary
space between the set and
the sides of the cupboard.

Installation
• Place the apparatus on a
flat, solid and stable surface
that can bear the weight of at
least 3 displays. If you use
an unstable cart or stand,
the set may fall, causing
serious injury to a child or
adult, and serious damage
to the equipment.

SAFETY INSTRUCTIONS

Summary of Contents for MFGD 3220 D




















Reviews: