Setting Up Video Routings
The MatrixPRO-II DVI 16x16 Router uses a more efficient
method of routing. A Video Input can be linked to multiple
Outputs with a single entry. Follow the steps below to set-
up a Video Routing from the front panel.
The MP-II DVI 16x16 Router System settings and
functions listed below can be changed using the “FUNC”
Key. Pressing the FUNCTION key will allow you to cycle
through the following features:
PC Program Operation
A PC Program has been included on the MP-II DVI product
CD. This program provides a user friendly graphic interface
(GUI) alternative to front panel and command input
operation. Additional info on this software can be found in
section 5 of the User’s Guide.
To install the program on your PC just run the MPII-
DVISetup program that is located in the MPII-DVI folder on
the product CD.
Input Selection Section
Provides 16 DDC/HDCP Compliant
DVI Inputs
Menu Display
Use Func Key for
System Set-Up and
Link Key to make
Input/Output
connections
Control Keys
Link Key to Set-Up Video Routings
Link then Shift to remove Routing
Func Key for System Set-up
“SHIFT ON PRESET” is currently unavailable.
This feature will be added in the future.
Menu Navigation
Input keys 1 thru 6 are
used to navigate in the
Function Menu
Output Selection
Section
Provides 16 DDC/HDCP
Compliant DVI Outputs
MatrixPRO-II DVI 16x16
Quick Start Guide
Visibly yours
BARC
1
2
3
9
8
7
6
5
4
1
2
3
9
8
7
6
5
4
INPUT
OUTPUT
DISPLAY
MatrixPRO-II DVI 16x16
MP-II DVI 16x16
Reset Switch
This switch puts the unit
into reset mode. Unplug
the AC power cord to
power the unit off
completely
Press the “Link” key
Select the Input Channel Number using the “Input”
Keys
Using the “Output” Keys, select all outputs you
would like to route the input to.
(pressing the
output key again will de-select that output)
Press the Enter Key after selecting your Outputs to
store your Video Routing
To Clear a routing from the front panel
Press the “Link” key then Press the “Shift” Key
“UnLink” should appear on the display
Press the “Input” key you would like to clear the
routings for.
Press the Enter Key to clear all outputs associated
with the “Input” you selected.
System Set-Up
Gateway
Subnet Mask
IP Address
MAC Address
(fixed value, can not be changed
from front panel)
UDP Port Number
(fixed value, can not be
changed from front panel
)
Video Generator
(1280x1024@60Hz Vertical Bars)
Monitoring Output
EDID Configure
HDCP Configure
Baud Rate
Control Lock
Factory Reset
Remote Configuration and Control
Web Control Panel Operation
The Web control panel provides a user-friendly GUI and
easy access to control the MP-II DVI. Additional
information on the Web Control Panel can be found in
section 6 of the User’s Guide.
To launch the Web control panel connect your PC to the
MP-II DVI through a switch or hub. A direct connection can
be made from a PC to the MP-II DVI but may require a
crossover cable. Set-up your PC Network Properties as
instructed in section 3.1 of the User’s Guide.
Launch your web browser and enter the IP address of the
MP-II DVI 16x16 into the URL address line. The factory
default IP address of the router is 192.168.0.246
Technical Support
(Europe, Middle East, Asia)
Telephone: 0800900410
Website: www.barco.com/support/eSupport.aspx
Technical Support (USA)
Telephone: (866) 374-7878
6 am to 10 pm (PST) 7 days/week
Websites: www.barco.com
www.barco.com/esupport
