![background image](http://html1.mh-extra.com/html/barco/hdf-w22/hdf-w22_user-and-installation-manual_4170864218.webp)
11. Lamp
11.7 CLO mode (Constant light output mode)
What can be done?
Constant Light Output allows to force a constant light output (set in the
CLO Target lumens
item) of the projector over a certain
period. This will eliminate uncontrolled light output drop caused by natural aging of the lamp. The light output is checked every 5
minutes, if the target is not met, the lamp power is adjusted.
Setting CLO off means that the lamp will operate at constant power (no power adaptation to meet constant light output).
In the illustration below, a normal light output curve is shown over the
fi
rst 1000 hours, image 11-16. By using CLO and setting the
target to 60% of the maximum light output, one will be able to operate during approximately 500 hours with a constant light output,
image 11-17.
100
20
40
60
80
200
400
600
800
1000
Relative Light Output (%)
Runtime (hrs)
Image 11-16
100
20
40
60
80
200
400
600
800
1000
Relative Light Output (%)
Runtime (hrs)
Constant Light Output
working area
Image 11-17
CLO mode setting On overrules the lamp power mode setting. Projector will always play in CLO mode using
the CLO target.
How to switch CLO mode
1. Press
Menu
to activate the menus and select
Lamp
→
Power
→
CLO mode
.
Image 11-18
Main menu, lamp
Image 11-19
Lamp, power
214
R5905158 HDF SERIES 08/12/2016
Summary of Contents for HDF W22
