background image

1. DP4K-L series accessory kit

1. DP4K-L SERIES ACCESSORY KIT

Purpose of this upgrade kit

This accessory kit may only be used to support and isolate the coupling of the hoses of the projector.

Where to use

There exist two accessory kits for the DP4K-L series. One for the DP4K-22L and DP4K-30L and one for
the DP4K-45L and DP4K-60L. For ordering numbers see Barco website

www.barco.com

.

About this document

This document gives a brief introduction of the accessory kit and explains with detailed step by step in-
structions how to install the insulation shells and the hoses support assembly. The latest version of this
document can be downloaded from the Barco website

www.barco.com

.

W

ARNING

:

The procedures below may only be performed by Barco trained and quali

fi

ed

technicians.

Overview

Kit content

Installation process

Assembling the support frame

Installing the support frame for hoses upwards

Installing the support frame for hoses downwards

Installing insulation shells projector side hoses upwards

Installing insulation shells projector side hoses downwards

Installing insulation shells on the chiller side

Installing the plastic catch basin

Installing the castor wheels

1.1

Kit content

In the box:

Insulation shells hoses upwards projector rear-left side (1 set, reference 1 image 1-1)

Insulation shells hoses downwards projector rear-left side (1 set, reference 2 image 1-1)

Insulation shells hoses upwards/downwards projector rear-right side (1 set, reference 3 image 1-1)

R5905882 DP4K-L ACCESSORY KIT 06/09/2017

3

Summary of Contents for DP4K-22L


















Reviews: