![background image](http://html1.mh-extra.com/html/barco/dp2k-slp-series/dp2k-slp-series_service-manual_474006360.webp)
R5906848 /04
DP2K SLP Series
360
Situation
Solution
Error appears on up to 4 laser
driver boards in the same
LDM: Defective LDM main
board.
This error will appear alongside with a yellow or even red taillight on the
projector.
Replace the entire LDM. See service procedure
“
, page 56.
Error appears on every laser
driver board that is physically
present in the LDM: Projector
is operating out of spec
This error will appear alongside with a yellow or red taillight on the
projector.
The projector
’
s is operating on a power higher than prescribed in the spec
and on the safety label. Make sure the supplied power is within spec.
If the problem persists, perform a test on your electrical circuit and check
for recurring voltage spikes. Make the necessary adjustments to your
electrical circuit to remove or filter out these spikes.
Code 20327:
“
LDM 1-2
–
LLS bank 2 drain voltage too high
”
For this error the same troubleshooting table can be applied to as for code
20323
:
“
LDM 1-3
–
LLS bank 1
drain voltage too high
”
.
Code 20331:
“
LDM 1-3
–
LLS bank 3 drain voltage too high
”
For this error the same troubleshooting table can be applied to as for code
20323
:
“
LDM 1-3
–
LLS bank 1
drain voltage too high
”
.
Code 20335:
“
LDM 1-2
–
LLS bank 1 current too high
”
Situation
Solution
Malfunction LDM board
Replace LDM board. See service procedure
, page 56.
Code 20339:
“
LDM 1-2
–
LLS bank 2 current too high
”
For this error the same troubleshooting table can be applied to as for code
20335
:
“
LDM 1-2
–
LLS bank 1
current too high
”
.
Code 20343:
“
LDM 1-2
–
LLS bank 3 current too high
”
For this error the same troubleshooting table can be applied to as for code
20335
:
“
LDM 1-2
–
LLS bank 1
current too high
”
.
Code 20359:
“
LDM 1-2
–
LLS bank 1 temperature too high
”
Situation
Solution
This error appears alone:
Insufficient cooling of light
source
•
Check the Cooling fluid level. Add in cooling fluid to the light source if
the level is too low.
•
Clean the front filter or replace with new one. See
Error appears alongside other
cooling related errors
Resolve cooling related errors first.
Code 20360:
“
LDM 1-2
–
LLS bank 1 temperature sensor shorted
”
Situation
Solution
Wiring issue
Check / reseat the cable between the LDM board and the LLS. If problem
persists, replace the cable.
Summary of Contents for DP2K SLP Series
