![background image](http://html1.mh-extra.com/html/barco/dp2k-slp-series/dp2k-slp-series_service-manual_474006314.webp)
R5906848 /04
DP2K SLP Series
314
Code 5280:
“
Ambient - Temperature too high
”
This error code is probably preceded by the warning code: ambient - temperature high
”
. The same
troubleshooting table can be applied to.
Code 5281:
“
Ambient - Temperature high
”
Situation
Solution
Ambient temperature too high.
Check the ambient temperature at the air inlets of the projector. Make sure
that the ambient temperature does not exceed 35°C (95°F).
Blocked dust filter.
Clean the large dust filter or replace with new one. See service manual
chapter
“
Malfunction air extraction
system.
Check the condition of the air extraction system. The air extraction system
must be capable of removing minimum 4 m³/min (140 CFM) per installed
DP2K-SLP Series digital projector.
Note:
limit the amount of extraction to a maximum of 5m
3
/min (180 CFM).
Excessive air extraction can dramatically speed-up contamination of the
projector air inlet filters, hence requiring more regular filter cleaning
interventions.
Defect temperature sensor.
Replace the ambient temperature sensor (reference 12 Image 25-51).
Malfunction Cinema Control
board.
Replace the Cinema Control board. See service manual chapter
Replacement of the Cinema Controller
12
Image 25-51
Code 5284:
“
Ambient - Temperature sensor open
”
Situation
Solution
Temperature sensor
disconnected.
Check if wire (reference 14 Image 25-52) of the ambient temperature
sensor (NTC) is connected with the Signal Backplane.
Defect temperature sensor.
Replace the ambient temperature sensor (reference 12 Image 25-53).
Malfunction Cinema Control
board.
Replace the Cinema Control board. See service manual chapter
Replacement of the Cinema Controller
Malfunction Signal Backplane.
Replace the Signal Backplane. See service manual chapter
“
,
Summary of Contents for DP2K SLP Series
