![background image](http://html1.mh-extra.com/html/barco/dp2k-s-series/dp2k-s-series_user-and-installation-manual_4093724043.webp)
7. Input & Communication
7.3
Projector Status
About the projector Status Light
The projector Status Light is located at the rear end of the projector (Tail Light). The projector Status Light is real time indicator of
the projector condition.
Image 7-3
Status overview
Depending on the condition of the projector the status light may have 4 colors: Green, Yellow, Red or Blue. Each color represent a
different state:
Blinking Green
Projector is booting up. (Fully booted up when Test Pattern button is green as well)
Green
Projector is running normally.
Yellow
Projector is running with warnings. Event can go on but a technical intervention will be necessary in
the near future to prevent a complete stop of the projector.
Red
Projector is in error state. Problem could prevent normal operation. Solve the problem before
continuing with the projector.
Blue
Projector runs in noti
fi
cation state. Maintenance action required. Lamp run time is exceeded.
New lamp must be installed.
Standby mode
In Standby mode the lamp of the projector is switched OFF but all the electronics of the projector remain fully operational. The
projector is ready to ignite the lamp and project the image. The status light is not different between Standby mode and Lamp ON
mode (fully operational).
Sleep mode
If the projector is in
Sleep
mode then the
status light
fl
ashes
every ten seconds. The color of the
fl
ash depends on the state of the
projector. In other words, the color of the
fl
ash will be green in normal state (no warnings, no errors, no noti
fi
cations).
In Sleep mode the total power consumption of the projector is less than 15W. No fans are turning and the Lamp Power Supply (LPS)
is switched OFF completely. Only the following functionalities of the projector remains active:
•
Cinema Controller
•
Local Keypad
•
Router and external switch fully functional
•
USB IN port type “B” (Virtual comport RS232)
•
USB OUT port type “A” (To power handheld devices [500mA MAX]. No other functionality supported)
•
GPIO
Pressing the Sleep button in Standby mode for 3 seconds puts the projector in Sleep mode. In case the projector is processing the
after cooling cycle then the projector goes in Sleep mode after
fi
nishing the after cooling cycle.
Pressing the Sleep button in Sleep mode for 3 seconds will awake the projector. The status light will blink for a few seconds (booting
up all inactive boards) and then lights up continuously.
Enter or leave Sleep mode can also be done via 2 dedicated projector command (USB/Ethernet), or via two prede
fi
ned Macros (not
editable) with GPIO, or via the Communicator.
The projector always boots up in the same mode (E.g. Standby or Sleep) as it was switched OFF.
The Sleep button is disabled if the lamp is ignited.
R5977692 DP2K-S SERIES 10/12/2012
39
Summary of Contents for DP2K-S Series
