manualshive.com logo in svg

Barco DP2K-E series, User And Installation Manual, Page: 131 / 163

Share
Download
Barco DP2K-E series User And Installation Manual Download Page 131

16. Removal and installation of the projector covers

16.7 Removal of the side cover plate of the Light Processor compartment

To access the side cover plate of the Light Processor compartment, the projector left side cover must

fi

rst be

removed. This procedure assumes that the projector left side cover is already removed.

C

AUTION

:

Opening the Light Processor compartment by removing the top cover plate or side cover plate will

result in a tamper event. An authorization to clear the security warning on the projector, after closing off the
Light Processor compartment, will be needed!

Necessary tools

3 mm Allen wrench.

How to remove the side cover plate from the Light Processor compartment?

1. Remove the four screws at the top of the cover plate and the two screws at the bottom of the cover plate (reference 1, image 16-9).

Use a 3 mm Allen wrench.

2. Slide the side cover plate left to disengage the cover, and then remove it.

1

1

Image 16-9

R5906693 DP2K-E SERIES 19/06/2015

127

Summary of Contents for DP2K-E series




































































































































































Reviews:

No comments