![background image](http://html1.mh-extra.com/html/barco/dp2k-c/dp2k-c_user-and-installation-manual_3937567013.webp)
13
R5905752 /16
DP2K C
Users definition
Throughout this manual, the terms SERVICE PERSONNEL and TRAINED PROJECTIONIST refers to
persons having appropriate technical training and experience necessary to be knowledgeable of potential
hazards to which they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and
ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures
to minimize the potential risk to themselves or other persons. The term USER and OPERATOR refers to any
person other than SERVICE PERSONNEL or TRAINED PROJECTIONISTS, AUTHORIZED to operate
professional projection systems.
The TRAINED PROJECTIONISTS may only perform the maintenance task described in the User &
Installation manual. All other maintenance tasks and service tasks must be performed by qualified SERVICE
PERSONNEL.
The DLP Cinema Systems are intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL
familiar with potential hazards associated with high voltage, high intensity light beams generated by lasers.
Only qualified SERVICE PERSONNEL and TRAINED PROJECTIONISTS, knowledgeable of such risks, are
allowed to perform service functions inside the product enclosure.
Restricted access location
To protect untrained persons and children, the projector must be installed in a
restricted access location
.
The definition of a
restricted access location
is a location for equipment where both of the following
paragraphs apply:
•
Access can only be gained by skilled persons (installer or service personnel) or by operators who have
been instructed and trained by a skilled person. The persons must have been instructed about the reasons
for the restriction applied to the location and about the precautions that shall be taken.
•
Access is only possible through the use of the tool or lock and key, or other means of security, and is
controlled by the authority responsible for the location.
Why a restricted access location: This product uses an extremely high brightness lamp. No person is allowed
to look directly into the lens or lamp. No person is also allowed to touch the exhaust system, due to hot
exhaust air.
This shall be physically impossible by creating sufficient separation height or by placing optional barriers.
Within the restricted area operator training is considered sufficient.
1.2 Important safety instructions
To prevent the risk of electrical shock
•
This projector should be operated from an AC power source. Ensure that the mains voltage and capacity
matches the projector electrical ratings. If you are unable to install the AC requirements, contact your
electrician. Do not defeat the purpose of the grounding.
•
Installation according to the local electrical code and regulations by qualified technical personnel only.
•
This product is equipped with a three-terminal barrier strip for the connection of a mono phase line with a
separate earth ground PE. If you are unable to install the AC Requirements, contact your electrician. Do
not defeat the purpose of the grounding.
•
The cross-sectional area of the conductors in the power supply cord shall be not less than 4 mm
2
or AWG
10.
•
The electronics of the projector must be powered either from a suitable UPS unit or from the power outlet
socket (UPS OUTLET) provided on the projector. For that reason an adapted short power cord (2-pole 3-
wire grounding) is added to the projector accessories to loop through the power.
•
The provided power output socket (UPS OUTLET) on the projector may only be used to provide power to
the projector electronics. Never connect other devices to this power output socket.
•
The circuit breaker(s) that must be provided in the power circuit(s) of the projector is considered as general
disconnect switch(es) to switch off the complete installation.
•
Switch off the projector and unplug the power cord from the UPS INLET for removal of all power from the
projector.
•
Warning: High leakage current. Earth connection essential before connecting supply.
•
Do not allow anything to rest on the power cord. Do not locate this projector where persons will walk on the
cord.
Summary of Contents for DP2K C
