1. Safety & environmental Information
The TRAINED PROJECTIONISTS may only perform the maintenance task described in the User & Installation manual. All other
maintenance tasks and service tasks must be performed by quali
fi
ed SERVICE PERSONNEL.
The DLP Cinema Systems are intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL familiar with potential
hazards associated with high voltage, high intensity light beams generated by lasers. Only quali
fi
ed SERVICE PERSONNEL and
TRAINED PROJECTIONISTS, knowledgeable of such risks, are allowed to perform service functions inside the product enclosure.
Restricted access location
To protect untrained persons and children, the projector must be installed in a
restricted access location
. The de
fi
nition of a
restricted access location
is a location for equipment where both of the following paragraphs apply:
•
Access can only be gained by skilled persons (installer or service personnel) or by operators who have been instructed and
trained by a skilled person. The persons must have been instructed about the reasons for the restriction applied to the location
and about the precautions that shall be taken.
•
Access is only possible through the use of the tool or lock and key, or other means of security, and is controlled by the authority
responsible for the location.
Why a restricted access location: This product uses an extremely high brightness lamp. No person is allowed to look directly into
the lens or lamp. No person is also allowed to touch the exhaust system, due to hot exhaust air.
This shall be physically impossible by creating suf
fi
cient separation height or by placing optional barriers. Within the restricted area
operator training is considered suf
fi
cient.
Owner’s record
The part number and serial number are printed on a label which is stuck on the respective part. Record these numbers in the spaces
provided below. Refer to them whenever you call upon your Barco dealer regarding this product.
Product article number
Product serial number
Dealer
1.2
Important safety instructions
To prevent the risk of electrical shock
•
This projector should be operated from an AC power source. Ensure that the mains voltage and capacity matches the projector
electrical ratings. If you are unable to install the AC requirements, contact your electrician. Do not defeat the purpose of the
grounding.
•
Installation according to the local electrical code and regulations by quali
fi
ed technical personnel only.
•
This product is equipped with a three-terminal barrier strip for the connection of a mono phase line with a separate earth ground
PE. If you are unable to install the AC Requirements, contact your electrician. Do not defeat the purpose of the grounding.
•
The cross-sectional area of the conductors in the power supply cord shall be not less than 4 mm
2
or AWG 10.
•
The electronics of the projector must be powered either from a suitable UPS unit or from the power outlet socket (UPS OUTLET)
provided on the projector. For that reason an adapted short power cord (2-pole 3-wire grounding) is added to the projector
accessories to loop through the power.
•
The provided power output socket (UPS OUTLET) on the projector may only be used to provide power to the projector elec-
tronics. Never connect other devices to this power output socket.
•
The circuit breaker(s) that must be provided in the power circuit(s) of the projector is considered as general disconnect switch(es)
to switch off the complete installation.
•
Switch off the projector and unplug the power cord from the UPS INLET for removal of all power from the projector.
•
Warning: High leakage current. Earth connection essential before connecting supply.
•
Do not allow anything to rest on the power cord. Do not locate this projector where persons will walk on the cord.
•
Do not operate the projector with a damaged cord or if the projector has been dropped or damaged - until it has been examined
and approved for operation by a quali
fi
ed service technician.
•
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
•
If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated
for less amperage than the projector may overheat.
•
Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short
circuit parts that could result in a risk of
fi
re or electrical shock.
•
Do not expose this projector to rain or moisture.
•
Do not immerse or expose this projector in water or other liquids.
2
R59770352 DP2K-C SERIES 22/03/2017
