Barco DP-1200 Installation Manual Download Page 30

Page: 30 / 134

3. Physical Installation

3.5

Connecting an UPS with the projector electronics

ARNING

Only use UPS units which are suitable for the DP-1200 digital projector. See chapter "Installation

requirements", page 10, for more information about the requirements of the UPS.

How to connect an UPS unit with the projector electronics?

1. Install the UPS unit according the instructions of the manufacturer and the local regulations.

2. Connect the power output cord (reference 1) from the UPS unit with the UPS INLET socket of the projector (upper socket).

3. Secure the UPS INLET socket using the small

xation plate and two thumbscrews. Use appropriate spacers to ensure that the

plug is captured without play.

4. Install the large

xation plate (reference 2) upon the power OUTLET socket of the projector (lower socket). This to prevent loosing

the

xation parts.

Image 3-12

AUTION

The electrical connection with the UPS INLET socket of the projector must be done with a certi

AC power supply cord (minimum 0,75 mm² or 18 AWG and minimum 300V)

AUTION

Do not use the power OUTLET socket of the projector to provide power to other equipment!

R59770242 DP-1200 06/01/2009

Summary of Contents for DP-1200







































































































































Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands

Barco DP-1200, Installation Manual

Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands