![background image](http://html1.mh-extra.com/html/barco/crpn-52b/crpn-52b_user-manual_473972033.webp)
www.projectiondesign.com
english
33
6.4 Setting custom color space and digital level
The projector will automatically try to set the correct color space and digital drive level based
on information from the source.
To manually override the automatically detected color space and digital level go to menu
entry PICTURE -> ADVANCED. Set the “digital color space and level” to manual and select
your color space and digital drive level.
6.5 Disabling IR receivers
The projector has 3 IR receivers as shown in chapter “4.1 Overview”.
These receivers can be individually disabled if necessary. Go to menu entry INSTALLATION >
IR FRONT / IR REAR to disable the receivers.
6.6 Controlling screens with triggers
The projector has two programmable triggers with 3.5 mm mini-jack connectors. These can
be used to enable or disable screens, curtains or other peripheral equipment.
To change trigger settings, go to menu entry INSTALLATION > TRIGGER
By default:
•
Trigger 1 is set to control a screen depending on whether projector is powered on or not.
•
Trigger 2 is set to control a screen depending on the aspect ratio of currently active
source.
Both triggers can be manually overridden both in the menu system and by using the com-
mand and control protocol through RS-232 or LAN.
6.7 Setting aspect trigger behavior
To customize the aspect trigger functionality, go to menu entry INSTALLATION > TRIGGER >
ASPECT TRIGGER BEHAVIOR. In this sub-menu it is selectable for which input aspect ratios
the trigger will be enabled.
6.8 Automatic power on/off
The projector can be automatically powered on or off by using the internal timer function or
DPMS.
6.8.1
Using the timer
The projector features a real-time clock that enables timing control. This means that the
projector can be programmed to switch on and off at certain pre-set times during a weekly
cycle.
To allow for a flexible schedule, 10 ‘programs’ are available. With each program, you can
define the switch on or switch off time for a single day (Monday to Sunday), all work days
(Monday through Friday), or week-end (Saturday and Sunday). One, several or all programs
can be active at the same time as desired. In this way, a flexible scheme can be established.
Observe the 24 hour time format. For more information, see the SETTINGS > TIMER menu.
The following example illustrates a case where the projector turns on at 08:00 in the morning
(8 am) and switches off at 20:00 (8 pm) on weekdays (Monday through Friday). Weekends
(Saturdays and Sundays), it turns on at 10:00 (10 am) and off at 18:00 (6 pm). VGA is used
as the source. For this, four programs are needed, 2 for on and two for off.
Summary of Contents for CRPN-52B
