![background image](http://html1.mh-extra.com/html/barco/clm-hd8/clm-hd8_user-manual_473954171.webp)
15. Maintenance
15. MAINTENANCE
About this chapter
This chapter contains detailed maintenance procedures like lens cleaning, etc. These procedures can easily be performed by the
operator of the projector.
Overview
•
•
Cleaning the exterior of the projector
•
15.1 Cleaning the lens
To minimize the possibility of damage to optical coatings, or scratches to lens surfaces, we have developed
recommendations for cleaning. FIRST, we recommend you try to remove any material from the lens by blowing
it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses.
Necessary tools
Toraysee
TM
cloth (delivered together with the lens kit). Order number : R379058.
How to clean the lens ?
1. Always wipe lenses with a CLEAN Toraysee
TM
cloth.
2. Wipe lenses in a one single direction.
Warning:
Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating.
3. Do not leave the cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth.
4. If smears occur when cleaning lenses, replace the cloth. Smears are the
fi
rst indication of a dirty cloth.
C
AUTION
:
Do not use fabric softener when washing the cleaning cloth or softener sheets when drying the
cloth.
Do not use liquid cleaners on the cloth as doing so will contaminate the cloth.
Other lenses can also be cleaned safely with this Toraysee
TM
cloth.
15.2 Cleaning the exterior of the projector
How to clean the exterior of the projector ?
1. Switch off the projector and unplug the power cord at the projector side.
2. Clean the housing of the projector with a damp cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild
detergent solution.
15.3 Level check of cooling liquid
What should be done ?
The projector is liquid cooled. When running with a low liquid cooling level then the cooling capacity is strongly reduced which results
in higher temperatures inside the projector. These higher temperatures can cause an interruption of your show as the lamps can be
switched off by the software as a preventive step.
To avoid this problem, we strongly advise to check at least every 3 months the cooling level in the cooling reservoir of the projector.
R59770057 CLM HD8 15/03/2010
167
Summary of Contents for CLM HD8
