9. Service Mode
9.3.1
Starting Up Projector Set-Up
Start up
1. Push the cursor key
↑
or
↓
to highlight
Projector Set-Up
and press
ENTER
to select. (menu 9-3)
The
Projector Set-Up
menu will be displayed. (menu 9-4)
SERVICE MODE
PROJECTOR SET UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
Select with
↑
or
↓
then <ENTER>
<EXIT> to return
Menu 9-3
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE: operating
COMMON ADDRESS: 0
BARCO LOGO
Select with
↑
or
↓
then <ENTER>
<EXIT> to return
Menu 9-4
9.3.2
Identification
What can be seen?
The Identification screen gives information concerning:
•
Projector address, to change the address of your projector, contact a qualified service technician.
•
Software version.
•
Configuration, possible installations: Front-ceiling, Front-table, Rear-ceiling, Rear-table.
•
Baud rate PC: transfer speed for communication with an IBM PC (or compatible) or MAC. The baud rate of the projector must
be the same as the baud rate of the connected computer. When there is a difference, contact a qualified service technician to
make the appropriate changes.
•
Text On/Off: indicates in operational mode if the bar scale and number indicator will be displayed and if warnings and failures
will be displayed (ON: displayed, OFF: not displayed). The status can be changed by pressing the
TEXT
key once on the RCU.
•
Serial No. : indicates the fabrication number of the projector. This number can be useful when calling for technical assistance.
How to start up Identification?
1. Push the cursor key
↑
or
↓
to highlight
Identification
and press
ENTER
to select. (menu 9-5)
The Identification screen will be displayed. (menu 9-6)
2. Press
EXIT
to return to the
Projector Set-Up
menu.
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE: operating
COMMON ADDRESS: 0
BARCO LOGO
Select with
↑
or
↓
then <ENTER>
<EXIT> to return
Menu 9-5
BARCO
CINE 7
Proj.
address:
001
Soft.
Version:
2.11
Config.:
Ceiling
Front
Baudrate PC: 9600
Text:
ON
Serial No.:
1035895
Menu 9-6
9.3.3
Total Run Time
What can be seen?
The total system run time since the first start up can be displayed plus the run time of the separate CRT’s since the last reset.
All projectors leave the factory after a burn-in period of approximately 100 hours.
R5976584 BARCO CINE7 26022003
85
Summary of Contents for CINE7 R9010040
