Connecting A Liquid Propane (LP) Gas Tank To Your Grill
1.
You will need to install the special fitting 3/8"FF (Female
Flare) x 3/8"MF (Male Flare) onto the outlet manifold so
that it is easier to attach the Hose and Regulator (see
Pg.6, Fig.8
). Attach LP Hose & Regulator assembly to
the fitting and ensure that both connections are gas tight
(Do NOT use Pipe Sealant on these flare connections).
2.
Open the left door. Pull out the LPG tank drawer (these
are not supplied with Natural Gas models).
Note:-Tank
drawer must be installed into the cart by the con-
sumer as per the instructions supplied with drawer
kit.
Place the 20 Ib cylinder with foot ring into the hole in
the drawer. See
Figure 17.
Make sure the tank valve is
in the OFF position. Make sure the gas tank is in the
upright position. Use the 5/16” x 90mm wing bolt provid-
ed to secure gas tank.
3.
Check the tank valve to ensure it has proper external
mating threads to fit the hose & regulator assembly pro-
vided. See
Figure 18.
(Type 1 connection per ANSI
Z21.58a-1998)
4.
Make sure all burner valves are in the OFF position.
5.
Inspect the valve connection port and regulator assembly.
Look for damage or debris. Remove any debris. Inspect
hose for damage. Never use damaged or plugged equip-
ment.
6.
When connecting the hose and regulator assembly to the
tank valve, hand tighten nut clockwise to a full stop. Do
not use a wrench to tighten because it could damage the
Quick Coupling Nut and result in a hazardous condition.
7.
Open the tank valve fully (counterclockwise). Use a
soapy water solution to check all connections for leaks
before attempting to light your grill. See ”Checking for
Gas Leaks” on
page 16
. If a leak is found, turn the tank
valve off and do not use your grill until the leak is
repaired.
Disconnecting An LP Gas Tank From Your Grill.
1.
Turn the burner valves and LP gas tank valve to the full
OFF position. (Turn clockwise to close.)
2.
Detach the hose and regulator assembly from the LP
gas tank valve by turning the Quick Coupling Nut coun-
terclockwise.
CAUTION: When the appliance is not in use, the gas
must be turned off at the supply tank.
Connecting Natural Gas To Your Grill
1.
You will need to install the Special fitting
3
/
4
” FF x
3
/
4
”
MP. Connect from the outlet manifold to the 12ft. Hose
and QD(Quick Disconnect) on cart model or the Natural
Gas Regulator to stainless steel flexline & shut-off valve
for built-in installation.
2a.
Built-in Model: Install the Shutoff Valve, Close Nipple,
Stainless Steel Flexline to the Natural Gas Regulator.
The Shutoff Valve must be intalled directly to the outlet
pipe and the Natural Gas Regulator must be connect
directly to the outlet manifold.
2b.
Cart model: Pass the hose through the hole in the cart
and connect the 12ft hose directly to the Natural Gas
Regulator. Make sure you have installed a Shutoff
Valve on the supply line.
3.
Turn the gas supply on and fully open the shutoff valve.
Use a soapy water solution to check all connections for
leaks before attempting to light your grill. See ”Checking
for Gas Leaks” on
page 16
. If a leak is found, turn the
gas supply off and do not use your grill until the leak is
repaired.
Figure 17
GAS
TANK
TANK
DRAWER
WING BOLT
Models YN662
and YN663
Figure 18
GAS
TANK
TANK
DRAWER
QUICK CONNECT
COUPLING NUT
- 1
7
-
Type 1 connection per
ANSI Z21.58a-1998
