background image

7

Maintenance

7.1

Maintenance schedule

Caution:
Clean the glass when it is dirty. If the glass is not cleaned when it is dirty the

glass can become permanently dull.

Table 2: Maintenance schedule

Task

Frequency

Procedure

Remove the ashes

When necessary

Refer to section 

7.2

Clean the glass

When necessary

Refer to section 

7.3

Maintenance by your fitter

Yearly

Refer to your dealer

Chimney sweep

Yearly (or more often when

necessary)

Refer to the Installation and

maintenance manual

Appliance inspection

Yearly

Refer to the Installation and

maintenance manual

7.2

Remove the ashes

1. Make sure that the appliance has cooled down and there are no glowing embers.
2. Remove the ashes with a small scoop.
3. Lift the grate with the operating hook and remove the grate.
4. Remove the ashtray and empty it.
5. Make sure there are no ashes in the space under the ash tray. Remove these ashes

when necessary.

6. Put the ash tray back in the appliance.
7. Put the grate back in the appliance.

7.3

Clean the glass

1. Make sure the appliance has cooled down and there are no glowing embers in the

combustion chamber.

2. To avoid any up swirl of ashes during cleaning, remove the ashes from the

appliance.

3. Clean the glass with a soft cloth, a sponge or paper. Use glass cleaner or ceramic

hob cleaner.

4. Make sure that the glass is dry. Water droplets can leave a mark on the glass.

Note:
Damaged or broken glass must be replaced before the appliance can be

used again.

Maintenance

Unilux-7 40

19

Summary of Contents for Unilux-7 40





























Reviews: