background image

SETTE™ 270 MANUAL

v2.1 August 27, 2019

6

HOPPER INSTALLATION

With the hopper lid in place, mount the hopper by lining up the hopper’s bean shutoff knob at the 
11:00 position (back left). Press the hopper down, and rotate clockwise until the alignment tabs 
on the front are aligned. Flip the bean shutoff knob to the “open” position and pour in desired 
quantity of roasted, whole coffee beans. 

ADJUSTING THE CONVERTIBLE DEVICE ARMS & PORTAFILTER HOOK:

The convertible device arms that hold the grounds bin can also be used to hold most 
popular brewing devices such as V60, AeroPress, Clever, and Able Kone. To convert to the 

portafilter holder position, push in on the right arm and swing it down and to the left (fig. 

A). To return to original position, push in on the right arm and rotate to the right and up 

(fig. B). The left arm will automatically move into position. 

When grinding directly into a portafilter, you must first convert the arms to portafilter 

holder position and swing the hook to the front. The hook is designed to support the top 

lip of your portafilter while the arms support the bottom of your portafilter. It is imperative 
that your hook is adjusted so that your portafilter sits level. To adjust the hook, loosen 
the 2mm hex screw that sits below the hook, adjust the portafilter hook up or down, and 

tighten screw once in the proper position. After you have adjusted your hook, run a test 

grind, if your portafilter does not sit level through the grinding process, you may need to 

make further adjustments.

fig. A

fig. B

Summary of Contents for sette 270














Reviews: