background image

will have different levels of noise reduction. The higher is the level, the louder will be the Squelch. By default, the Squelch 
level of H-888S is set on level 4. Make sure you do not set an excessively high squelch level because in this case you may not 
be able to receive weaker signals. On the other hand an excessively low Squelch value could enable the Squelch even when 
no signals are present. Squelch must always be adjusted when no signals are present. The Time Out timer is settable from 30 
sec to 270 sec. only through the programming software. This feature is disabled by default. 

CTCSS/DCS tones   

CTCSS and DCS tones are similar to access codes and enable the radio to communicate only with the users that are tuned on 
the same channel and have set the same code. For each channel, you can set up to 50 CTCSS tones and 210 DCS codes. The 
CTCSS/DCS  tones  are  a  sort  of  “access codes”  and  enable  the  radio  to  communicate  only  with  the other  users  set  on  the 
same  frequency  and  on  the  same  CTCSS/DCS  tone.    Undesired  signals  coming  from  other  stations  set  on  the  same 
frequency but with different CTCSS/DCS tones won’t be received.   

Flashlight   

With H-888S turned on, shortly press the 

Side key 2

 to turn on/off the flashlight at the top side of the radio. 

Prompt voice switch settings 

The  encoder  is  selected  to  the 

10th

  channel.  Press  and  hold  the 

PTT

  and 

Side  Key  1

  to  turn  on  the  radio,  and  turn  the 

prompt voice on or off. 
Turn on the prompt voice function, and there will be voice prompts when the encoder is turned on or operated. If you turn 
off the prompt voice function, there is only a “beep” prompt when you turn on or operate the encoder. 

Emergency alert function 

If necessary, you can pre-program the 

Side Key 1

 into the Alarm function via CPS programming software. 

Turn  on  the  radio,  short  press  the 

Side  Key  1

  to  turn  on  the  alarm  function.  Press  the 

Side  Key  1

  again  to  release  the 

emergency alarm status. 

VOX 

The VOX feature enables hands free conversations without using PTT: just speak in the direction of the microphone and the 

Summary of Contents for H-888S
















Reviews: