Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: [email protected]
WORLD BEAM
®
QS30 – DC Voltage
WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for
one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its
manufacture found to be defective at the time it is returned to the factory during the warranty
period. This warranty does not cover damage or liability for the improper application of
Banner products. This warranty is in lieu of any other warranty either expressed or implied.
P/N 119167 rev. A
Supply Voltage and Current
10 to 30V dc (10% maximum ripple) at less than 40 mA, exclusive of load
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Output Configuration
Bipolar: One current sourcing and one current sinking
Rating: 100 mA maximum each output at 25°C
Off-state leakage current: NPN: less than 200 µA
PNP: less than 10 µA
ON-state saturation voltage: NPN: less than 1.6V @ 100 mA
PNP: less than 2.0V @ 100 mA
Protected against false pulse on power-up and continuous overload or short
circuit of outputs
Output Response Time
Opposed Mode: 5 milliseconds ON and OFF
All others: 2 milliseconds
NOTE: 100 millisecond delay on power-up; outputs do not conduct during
this time
Repeatability
Opposed Mode: not applicable
All others: 500 microseconds
Cutoff Point Tolerance
Fixed-Field only: ±5% of nominal cutoff distance
Indicators
2 LED indicators on sensor top:
Green ON steady: Power ON
Yellow ON steady: Light sensed
Green flashing: Output overloaded Yellow flashing: Marginal excess gain
(except receivers)
(1.0 to 1.5x excess gain)
Large oval LED indicator on sensor back (except emitters):
Yellow ON steady: Output conducting
Adjustments
Diffuse, Retroreflective, and Polarized Retroreflective mode models:
Single-turn Sensitivity (Gain) adjustment potentiometer
All models: Selectable Light/Dark Operate is achieved via the gray wire, as
described below.
Opposed, Retroreflective, and Polarized Retroreflective models:
Light Operate - Low (0 to 3V)*
Dark Operate - High (open or 5 to 30V)*
Diffuse and Fixed-Field models:
Light Operate - High (open or 5 to 30V)*
Dark Operate - Low (0 to 3V)*
* Input impedance 10 k
Ω
Construction
ABS housing, rated IEC IP67; NEMA 6; Acrylic lens cover
3 mm mounting hardware included
Connections
2 m (6.5') or 9 m (30') 5-wire PVC cable, or 5-pin Euro-style integral QD
connector
Operating Conditions
Temperature: -20° to +70° C (-4° to +158° F)
Relative Humidity: 90% @ 50° C (non-condensing)
Vibration and Mechanical Shock
All models meet Mil. Std. 202F requirements method 201A (vibration: 10
to 60 Hz max., double amplitude 0.06", maximum acceleration 10G). Also
meets IEC 947-5-2; 30G 11 ms duration, half sine wave.
Certifications
Specifications
Quick-Disconnect (QD) Cables
Additional information on this product is immediately available online at
www.bannerengineering.com/119165
View or download additional information, including excess gain curves, beam patterns and accessories.
For further assistance, contact a Banner Engineering Applications Engineer at (763) 544-3164 or (888) 373-6767.
Style
Model
Length
Dimensions
Pin-Out
5-pin
Euro-style
straight
MQDC1-506
MQDC1-515
MQDC1-530
2 m (6.5')
5 m (15')
9 m (30')
5-pin
Euro-style
right-angle
MQDC1-506RA
MQDC1-515RA
MQDC1-530RA
2 m (6.5')
5 m (15')
9 m (30')
White Wire
Blue Wire
Black Wire
Brown Wire
Gray Wire
M12 x 1
ø 15 mm
(0.6")
44 mm max.
(1.7")
38 mm max.
(1.5")
M12 x 1
ø 15 mm
(0.6")
38 mm max.
(1.5")
