Banner QS30LLP Manual Download Page 1

Polarized Retroreflective Laser Sensors

 

 

Features

• Visible class 1 laser with small, effective beam size
• Excellent optical performance throughout sensing range, even close up
• Easy push-button SET options: Maximum Excess Gain or Low-Contrast

SET, depending on model, plus Manual Adjust

• Easy-to-read operating status indicators, with 8-segment bargraph display
• Bipolar discrete outputs, PNP and NPN
• Selectable 30 millisecond OFF-delay
• Models available with 2 m or 9 m (6.5' or 30') cable or integral quick-discon-

nect

• Tough ABS housing rated IEC IP67; NEMA 6
• Compact housing, mounting versatility – popular 30 mm threaded nose or

side-mount

Excellent for applications where high sensing power and small beam size are important. Operates over sensing ranges typically accom-
plished only by conventional opposed-mode photoelectrics; uses a special filter to polarize the emitted light, filtering out unwanted reflec-
tions from shiny objects.

Models

Model

Range and Use

Spot Size at Fo-
cus

Cable*

Supply

Output Type

QS30LLP

0.2 to 18 m (0.67 ft to 60 ft)
Maximum Excess Gain SET
for Long-Range Applications

Approx. 4 mm at
10 m (0.16 in at 33
ft)

2 m (6.5 ft) 5-wire Ca-
ble

10 to 30V dc

Bipolar NPN /
PNP

QS30LLPQ

Integral 5-pin Euro-
style QD

QS30LLPC

0.2 to 18 m (0.67 ft to 60 ft)
Low-Contrast SET for Small
Object Detection

2 m (6.5 ft) 5-wire Ca-
ble

QS30LLPCQ

Integral 5-pin Euro-
style QD

* 9 m (30 ft) cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., QS30LLP W/30). A model with
a QD connector requires a mating cable (see 

Quick-Disconnect Cables 

on page 10).

WARNING: Not To Be Used for Personnel Protection
Never use this product as a sensing device for personnel protection. Doing so could lead to serious
injury or death.
 This product does NOT include the self-checking redundant circuitry necessary to allow its
use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-
energized sensor output condition.

WORLD-BEAM QS30 LLP and LLPC

 

 

P/N 112355 Rev. C

12/18/2013

0 112355

5

Summary of Contents for QS30LLP













Reviews: