background image

16

The rear socket panels on BeoVision

MX 8000 allow you to connect the

signal input cables as well as a

variety of extra equipment.

The V.TAPE and AV sockets are

available for connection of extra

equipment.

Any equipment you choose to

connect to these sockets must be

registered in the BeoVision MX 8000

CONNECTIONS menu. Refer to

BeoVision MX 8000 CD-rom and the

chapter 

Register extra equipment

for

further instruction.

The presence or absence of the

sockets depends on which optional

extras are built into your BeoVision

MX 8000.

Socket panel on the rear

Speaker and digital input socket panel

These sockets are only available if your BeoVision

MX 8000 has a built-in digital surround sound

module.

Refer to the BeoVision MX 8000 CD-rom and the

chapter 

Loudspeaker setup – surround sound

for

further information.

STAND

For connection of a motorised stand.

AV

21-pin socket for AV connection of a second

decoder, a DVD player, a set-top box or similar

devices. You can also connect other types of

auxiliary equipment or an Expander box for further

connections.

V.TAPE

21-pin socket for the AV connection of a BeoCord

V 8000 video tape recorder, a set-top box, a

primary decoder or another video tape recorder.

You can also connect other types of auxiliary

equipment to the V.TAPE socket. If the connected

video tape recorder is a BeoCord V 8000, the

tuned TV programs etc. will be downloaded to the

video tape recorder when the BeoVision MX 8000

TV is tuned in.

MASTER LINK

For connection of a compatible Bang & Olufsen

audio system. This socket is only available if your

BeoVision MX 8000 is equipped with the 

Master Link module.

The socket is also used for BeoLink distribution of

sound and picture throughout the house.

LINK TV

Aerial output socket for distribution of video

signals to other rooms. This socket is only available

if your BeoVision MX 8000 is equipped with the

built-in system modulator.

TV

Aerial input socket for your external TV aerial (or

cable TV network) signal. If your BeoVision 

MX 8000 is equipped with the built-in system

modulator, connect your external TV aerial to the

TV socket located below the socket marked LINK.

POWER LINK

For connection of external Bang & Olufsen

loudspeakers.

~

Socket for connection to the mains.

IR OUT

For connection of a set-top box. (Only available

when a Set-top Box Controller is built into your

BeoVision MX 8000). 

STAND

V. TAPE

MASTER LINK

POWER LINK

TV

LINK TV

IR-OUT

AV

SUBWOOFER

FRONT

REAR

FRONT

REAR

INPUT 1

INPUT 2

Summary of Contents for BeoVision MX 8000





































Reviews: