background image

Installation and wiring 

5.4.3 Grounding concept - Functional ground

Functional ground is a current path of low impedance between circuits and ground. It is used to improve immunity

to interference, for example, and not as a protective measure. It serves only to divert interference, not to protect

against contact with persons.
The device is equipped with 2 functional ground connections:

Functional ground connection of the power supply

Ground connection

The following points must be observed to ensure that electrical interference is safely diverted:

Connect the device to the central grounding point (e.g. the control cabinet or the system) using the shortest

possible low-resistance path.

Cable design with at least 2.5 mm² per connection. If a cable with wire end sleeve is used at terminal block

0TB103.9 or 0TB103.91, a cable with a maximum of 1.5 mm² per connection is possible.

Observe the shielding concept of the conductors. All data cables connected to the device must be shielded.

The functional ground on the B&R device is marked with the following symbol: 

Legend

1

Ground connection 

2

Power supply conn24 VDC pin 2

3

Central grounding point

a

At least 1.5 mm²

b

At least 2.5 mm²

-

34

SDL4 Converter User's manual V 2.01

Summary of Contents for SDL4














































Reviews: