B&K ST1200 Owner'S Manual Download Page 19

Page 17

B&K Components Ltd., referred to herein as B&K, warrants your B&K equipment against all defects in
material and workmanship for a period of five years from the date of purchase.  This warranty applies
only to the original purchaser and only to equipment in normal residential use and service.  Defective
equipment must be returned to B&K, prepaid, accompanied by sufficient payment to cover the cost of
return shipping and handling, and will be repaired or replaced at the discretion of B&K whose decision
as to the method of reparation will be final.

This warranty shall not apply to any equipment which is found to have been improperly installed,
incorrectly fused, misused, abused, or subjected to harmful elements, used in any way not in
accordance with instructions supplied with the unit, or to have been modified, repaired or altered in any
way without the expressed, written consent of B&K.  This warranty does not apply to the cabinet, the
remote controller, or appearance items such as the faceplate, control buttons, or display lenses, nor
does it cover any expenses incurred in shipping the unit to and from the manufacturer’s service depot.

No warranty, implied or otherwise created by State law shall extend beyond the terms of this warranty
and B&K shall not be liable for any incidental or consequential damage arising out of a defect in material
or workmanship of the unit during the terms of this warranty or thereafter.  Some States do not allow the
exclusion or limitation of incidental or consequential damages and the foregoing exclusions may not
apply to you.

This warranty gives you specific legal rights.  Your may also have other rights which vary from State to
State.

No agent, representative, dealer or employee of B&K has the authority to increase or alter the
obligations or terms of this warranty.

B&K Components Ltd.

No equipment may be returned to B&K Components Ltd. Without a RETURN AUTHORIZATION. 
Should you find it necessary to return equipment to B&K, for any reason, a RETURN AUTHORIZATION
(RA) number must be issued by B&K in respect of the equipment being returned.  You may request an
RA number by calling B&K at the numbers below.  We ask that you provide the following information at
that time.

1.

Your name, address, and phone number.

2.

The model and serial number of the equipment being returned.

3.

A description of the problem being experienced.

Your call will be referred to a Technical Service Representative who will work with you to resolve the
problem.  If it is determined that the unit must be returned for repair, an RA number will be issued.

B&K Components Ltd. 2100 Old Union Road, Buffalo New York 14227

  1-800-543-5252 or 1-716-656-0023 

Summary of Contents for ST1200





















Reviews: