Tri-Tran
™
rECEiVEr
INSTALLATION INSTRUCTIONS
Part No. 62851
72963 Installation Instructions. Revision 1 September 2008
Thank you for purchasing the B&D Tri-Tran™ plug in two
channel Receiver. Familiarise yourself with the following
instructions prior to commencing set up. Store this information
in a safe place for future reference. The B&D Tri-Tran™
receiver has transistors on board which provide an open
collector contact for controlling virtually any electronic garage
door or gate.
BranD OF TranSMiTTErS
The first memory location sets the type of transmitters which
can be stored into the receivers memory. It either can be B&D
Tri-Tran™ or ATA TrioCode™ transmitters. For example if first
transmitter stored is TrioCode™ then rest of transmitters can
only be the TrioCode™ type and mixing of TrioCode™ and
Tri-Tran™ is not possible. By deleting all stored transmitter
codes from the receivers memory will allow you to choose either
TrioCode™ or Tri-Tran™ transmitters again.
UniVErSaL PrOGraMMEr
A B&D Universal Programmer can be used to set timer
(adjustable from 0.00 to 655.34 seconds), Edit, back up /
restore transmitters.
STOrinG TranSMiTTEr CODE
1. Press and hold SW1 (for channel 1) or SW2 (for channel
2) on the receiver board. The LED D1 will start to flash.
2. Press the transmitter button you would like to use to
control the device for two seconds. The LED will start to
flash faster.
3. Release the transmitter button and pause for two
seconds. Press the same button again for two seconds.
The LED will stay on for a second and then turns off.
4. Release SW button.
5. Press the transmitter button to test operation.
DELETinG a SinGLE TranSMiTTEr’S CODE
1. Press and hold SW1 (for channel 1) or SW2 (for channel
2) on the receiver board. The LED will start to flash.
2. Press the transmitter button you would like to remove
from receivers memory for two seconds. The LED will
start to flash faster.
3. Release the transmitter button and pause for two
seconds. Press the same button again for two seconds.
The LED will slowly flash two times.
4. Release SW button.
5. Press the transmitter button to confirm that it has been
removed.
DELETinG aLL STOrED TranSMiTTEr CODES
1. Turn the power off to the receiver.
2. Press and hold SW1 button.
3. While holding SW1 turn power on again. After 15
seconds the Coding LED will illuminate to indicate that
the receivers memory has been cleared.
4. Release SW1. All the stored codes should now be deleted.
Confirm this by pressing the transmitters previously used to
operate the device. There should be no response.
COaXiaL COnnECTiOn
An optional coaxial antenna is available for use with the receiver
in difficult reception areas. The antenna has to be mounted
as high as possible so that it is not obstructed, e.g. on top of a
fence, or on a wall at the front of a garage, etc. Connect the core
of coaxial lead to replace the existing antenna wire (outer screw
socket). Connect shield to the spare (inner) screw socket.
HarnESS
User may have to cut and strip wires to connect to different
openers. Cut and leave white wire if the second channel is not
used.
1
2
3
4
5
6
SW2
SW1
ANTENNA
SHIELD
PG3 CONNECTOR
PIN1 = OPEN COLLECTOR CH1 OUT PUT.
PIN2 = 9 TO 24 VOLT DC INPUT SUPPLY.
PIN3 = NOT USED
PIN4 = OPEN COLLECTOR CH2 OUT PUT.
PIN5 = GROUND. PIN 6 = GROUND.
D1
Tri-Tran
TM
Tri-Tran
TM
Transmitter
RED
RED
BLUE
BLACK
WHITE
BLUE
WHITE
BLACK
5
380
NOM
26 NOM
Harness to use with receiver
