USOTL4-1405 - 2/2
© 2004 by B&B Electronics. All rights reserved.
pn 5253-r4
B&B ELECTRONICS
DECLARATION OF CONFORMITY
Manufacturer’s Name:
B&B Electronics Manufacturing Company
Manufacturer’s Address:
P.O. Box 1040
707 Dayton Road
Ottawa, IL 61350 USA
Model Numbers:
USOTL4
Description:
Optically Isolated USB to RS-422/485 Converter
Type:
Light industrial equipment
Application of Council Directive: 89/336/EEC
Standards: EN
55022
EN
61000-6-1
EN 61000 (-4-2, -4-3, -4-4, -4-5, -4-6, -4-8, -4-11)
Robert M. Paratore, Director of Engineering
#6.
You will also need to continue to install the serial
port the same as installing the converter. Click the
Next
button followed by the
Finish
button. It will take a
couple seconds for the serial port to be installed.
USOTL4
RS-422
Device
TDA(-)
TDB(+)
RDA(-)
RDB(+)
GND
RDA(-)
RDB(+)
TDA(-)
TDB(+)
GND
USOTL4 in a four-wire set-up
with all switches in the OFF position.
RS-485
Network
USOTL4
RS-485
Device
TDA
(-)
RDA
(-)
GND
TDB(+
)
RDB
(+)
Data (B)
Data (A)
Data (B)
Data (A)
GND
USOTL4 in a two-wire set-up
with all switches in the ON position.
RS-485 Control
No special software is required to control the RS-485 receiver
or transmit line driver. The driver is automatically enabled
during each byte transmitted in RS-485 mode. The
transmitter is always enabled in RS-422 mode. The receiver
is tri-stated during each byte transmitted in the echo-off
mode. The receiver is always enabled in the echo-on mode.
There are 4.7k Ohm pull-up/pull-down resistors on the RDA
and RDB lines. A termination resistor may be added to R16 if
needed. See B&B’s RS-422/RS-485 Application Note
(available on our website or by mail) for more information on
termination and DC biasing of an RS-485 network.
Dip Switch Set-up
Dip switches allow the module to be configured for two-wire
or four-wire, RS-422 or RS-485 modes. In two-wire mode the
TDA (-) and RDA (-) are tied together and so are TDB (+) and
RDB (+), making multi-dropping this converter into an existing
network easy.
Switch OFF
ON
One
TD always enabled
(TD 422)
TD only enabled during data
transmission.
(TD 485)
Two
RD always enabled
(ECHO ON)
RD disabled during data
transmission.
(OFF)
Three Four-wire
mode
(4-Wire)
Two-wire mode
(2-Wire)
Four Four-wire
mode
(4-Wire)
Two-wire mode
(2-Wire)
Specifications
Dimensions:
2.7 x 5.1 x 0.9 in (6.9 x 13.0 x 2.3 cm)
Temperature Range:
0 to 70
o
C (32 to 158
o
F)
RS-485/422 Baud Rate: Up to 460.8 kbps
USB Baud Rate:
High speed device
USB Power:
Low power device (draws < 100mA)
Operating System:
Windows 98/SE, 2000, ME, XP
Accessories: Driver CD
Isolation: 2000 V RMS
#5.
The screen above will appear. Click the
Finish
button to complete the installation.
International Headquarters:
707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA
815-433-5100 Fax 433-5104
www.bb-elec.com [email protected] [email protected]
European Headquarters:
Westlink Commercial Park Oranmore Co. Galway Ireland
+353 91 792444 Fax +353 91 792445
www.bb-europe.com [email protected] [email protected]
PRODUCT INFORMATION
