background image

1. SAFETY INSTRUCTION

1. Safety instruction

Please, observe the following instructions:

The router must be used in compliance with all applicable international and national laws
and in compliance with any special restrictions regulating the utilization of the router in
prescribed applications and environments.

To prevent possible injury to health and damage to appliances and to ensure that all
the relevant provisions have been complied with, use only the original accessories.
Unauthorised modifications or utilization of accessories that have not been approved
may result in damage to the router and in a breach of applicable regulations. Unautho-
rized modifications or utilization of accessories that have not been approved may result
in the termination of the validity of the guarantee.

The router can not be opened.

It must not be exceeded by the maximum voltage 30 V DC power connector on the router.

Do not expose the router to extreme ambient conditions. Protect the router against dust,
moisture and high temperature.

The router should not be used at petrol stations of flammable and explosive materials.
We remind the users of the duty to observe the restrictions concerning the utilization
of radio devices at petrol stations, in chemical plants, or in the course of blasting works
in which explosives are used.

When using the router in the close proximity of personal medical devices, such as cardiac
pacemakers or hearing aids, you must proceed with heightened caution.

If it is in the proximity of TV sets, radio receivers and personal computers, the telephone
may cause interference.

It is recommended that you should create an appropriate copy or backup of all the im-
portant settings that are stored in the memory of the device.

1

Summary of Contents for Conel XR5i v2




































Reviews: