29
GB
B
A
M
A
T
O
Bavarian Machine Tools
If the carbon is worn to a length of 6 mm, or if the
spring or contact wire are burned or damaged, it is
necessary to replace both brushes. If the brushes are
found to be usable following removal, it is possible to
reinstall them.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the follow
ing parts are therefore also required for use as con
sumables.
Wear parts*: Carbon brush, saw blade, battery, table
insert, sawdust bag, Vbelts
* Not necessarily included in the scope of delivery!
11. Storage
Store the device and its accessories in a dark, dry
and frostproof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from
dust and moisture.
Store the operating manual with the electrical tool.
12. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions.
The customer‘s mains connection as
well as the extension cable used must al-
so comply with these regulations.
•
The product meets the requirements of EN
61000311 and is subject to special connection
conditions. This means that use of the product at
any freely selectable connection point is not al
lowed.
•
Given unfavorable conditions in the power supply
the product can cause the voltage to fluctuate tem
porarily.
•
The product is exclusively intended for use at con
nection points that have a continuous currentcar
rying capacity of at least 100 A per phase.
•
As the user, you are required to ensure, in consul
tation with your electric power company if neces
sary, that the connection point at which you wish
to operate the product meets the specified require
ments.
Important information
In the event of an overloading the motor will switch
itself off. After a cooldown period (time varies) the
motor can be switched back on again.
•
Important! The work to change and align the saw
blade (7) must be carried out correctly.
8.11 Using the laser (Fig. 3/19/20)
•
To switch on:
Move the ON/OFF switch of the la
ser (34) to the “1” position. A laser line is projected
onto the material you wish to process, providing an
exact guide for the cut.
•
To switch off:
Move the ON/OFF switch of the la
ser (34) to the “0” position.
•
Replacing the battery:
Switch off the laser
(33). Remove the battery compartment cov
er (36). Remove the batteries and replace with
new batteries (2 x 1.5 Volt Type LR 03 Micro,
AAA) Check that the battery terminals are po
sitioned correctly when inserting new batter
ies. Close the battery compartment (35) again.
8.12 Adjusting the laser (Fig. 21)
If the laser (33) ceases to indicate the correct cutting
line, you can readjust the laser. To do so, open the
screws (38) and set the laser by moving sideways to
that the laser beam strikes the teeth of the saw blade
(6).
9. Transport
•
Tighten the set screw (26) in order to lock the ro
tary table (14)
•
Activate the release lever (3), press the machine
head (4) downwards and secure with the safety pin
(23). The saw is now locked in its bottom position.
•
Fix the saw’s drag function with the locking screw
for drag guide (20) in rear position.
•
Carry the equipment by the fixed saw table (15).
•
When reassembling the equipment proceed as de
scribed under section 7.
10. Maintenance
m
Warning!
Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time
using a cloth. In order to extend the service life of the tool,
oil the rotary parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive prod
ucts.
Brush inspection
Check the carbon brushes after the first 50 operat
ing hours with a new machine, or when new brushes
have been fitted. After carrying out the first check, re
peat the check every 10 operating hours.
