Bally ProSlot 6000, Setup And Operation

Page: 40 / 444

SETUP AND OPERATION
2-40
©2004 Bally Gaming and Systems
ProSlot® 6000
| - Revised, || - New
#8 - Slot Communications
The Slot Communication test confirms the serial ports are
working properly. The test checks for shorts and opens.
Press and release the
TEST
button until 08 d appears
in
WIN PAID
, indicating the Slot Communications test
is selected. A dash ( - ) appears in the
CREDIT
display if
a channel is not found.
Next, 081d appears in
WIN PAID
. The test checks for shorts
on ports 1A, 1b, 2A, 2b, 3A, and 3b. An S appears in
the
CREDIT
display if a short exists. When the machine is
finished testing for shorts, the message 082d appears
in the
WIN PAID
at which time a test pulse is transmitted.
Each receiving port is tested for reception of a signal.
Physical connection is required. The following table lists
the ports and its locations on the game:
Port Duart Name Location Connector Jumper
0 1A (U38) Link RS-485 Backplane
Board
J14 CBL-30284-0001
1 1B Auxiliary
MPU
Board
J3 CBL-30293-0001
2 2A (U39) Bill Acceptor Backplane
Board
J4 CBL-20243-0001
3 2B System
Backplane
Board
J10 CBL-30298-0001
4 3A (U37) Spare RS-232 Backplane
Board
J18 CBL-30283-0001
5 3B Spare RS-485 Backplane
Board
J15 CBL-20239-0001
Diagnostic Tests and Functions
Note: Reel tilts generated with the
main door open are not recorded.
#7 - Reel Tilt and System Reset Records
Test #7 displays the number of reel tilts and system
resets recorded.
To enter, press and release the
TEST
button until the
07
d appears in
WIN PAID
, indicating Reel Tilt and System
Reset Records is selected. W
IN PAID
shows a 2 in
the third position indicating information on reel tilts is
being displayed. The
CREDIT
display shows the total
number of reel tilts that occurred.
To view information on tilt types
4 through 7, turn the
audit key switch once. To view information on resets
8 through b , turn the audit key switch again. The
Message Center automatically cycles through the
reset types. The reset type number appears in the
third position of
WIN PAID
, and the total number of tilts
appears in the
CREDIT
display.
An MPU board with CPU error resets should be
removed from service.
Tilt Description
2 Reels Moving Improperly
4 Accelerating Improperly
5 Running Improperly
6 Decelerating Improperly
7 Reels in Wrong Position
8 Power Fail Resets
9 Door Resets
A Hardware Resets
B CPU Error Resets
Note: Test #8 cannot test signal
reception without loopback jumpers
installed.
#9 - Display Test
Test #9 tests the Message Center. Observe to make
sure all LED segments in each of the 10 display
positions are properly functioning.
Press and release the
TEST
button until 09 d appears
in
WIN PAID
, indicating the Display test is selected. A
pattern cycles in the Message Center that illuminates
each segment and decimal point.
#6 - Reel Tape Test
Test #6 provides a means for the Operator to confirm
that the reel symbols are in the correct positions and
match the information listed in the SMI document.
To begin, press and release the
TEST
button until
06 d appears in
WIN PAID
, indicating the Reel Tape test
is selected. The reels slow-spin to position 0 and stop.
After a pause the reels simultaneously advance to
position 21. The
CREDIT
display shows the reel position.
The sequence continues until this test is exited.