BALLHOG Ascent Apex Manual Download Page 14 | Manualshive

Page: 14 / 20

background image

888.496.5137

b

all

h

og

g

oals.com

PAGE 14

STEP 9 -BACKBOARD ATTACHMENT

•

Now that the backboard is attached, take a moment to check to see if the backboard is square to the playing area.

•

If any adjustment needs to be made, simply loosen the four (#3) nuts from Step 7 ever so slightly and rotate the pole on the anchor.
DO NOT completely remove any of the (#3) nuts.

•

Once the backboard is square with the playing area tighten the four (#3) nuts completely.

Experienced Installer Tip:

As you tighten the four (#3) nuts completely, check the backboard to see if it is plumb. Place a level on the

face of the glass running from top to bottom and on the side of the backboard on the outside of the aluminum trim. The four (#3) nuts
located below the baseplate of the pole can be adjusted to fine tune the backboard. Once you are satisfied, double check to make sure
the four (#3) nuts are tight.

This area intentionally left blank.

«
...
12
13
14
15
16
...
»

Summary of Contents for Ascent Apex





















Reviews:

No comments

Related manuals for Ascent Apex

MMAC-Plus 9F116-01

Brand: Cabletron Systems Pages: 4

Brand: Caberg Pages: 16

Brand: IBAIONDO Pages: 7

Brand: QIMMIQ Pages: 16

Brand: QA1 Pages: 10

Brand: GBRacing Pages: 2

KTS-WB61141142 Series

Brand: SICK Pages: 8

Brand: Oki Pages: 2

Brand: Takex Pages: 4

Brand: Lincoln Electric Pages: 32

Brand: Cycling Sports Group Pages: 8

Brand: PSF Pages: 2

Brand: IKAR Pages: 72

Brand: Cerlic Pages: 20

Silver Billet KR-800

Brand: Havis-Shields Pages: 1

Brand: Ikelite Pages: 4

Brand: Yeti Pages: 13

echoflex OWS-DT-UW-120/277

Brand: ETC Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands