Baldwin Boxall BVRAMB Operating Instructions Manual Download Page 12 | Manualshive

Page: 12 / 16

background image

BVRAMB Ambient Noise Microphone
Installation Instructions

6

BVRAMB issue 4

C O M M U N I C A T I O N S

Figure 2.3 — Typical Connection details for BVRDCI

N

OTE

: For BVRDCI connections the relevant jumper must be set to "0V".

Group1 is for Inputs 1-4, Group2 is for inputs 5-8 etc.

N

OTE

: The system cabling for the BVRAMB modules does not need to be

screened as there are no audio paths.

www.acornfiresecurity.com

www.acornfiresecurity.com

«
...
10
11
12
13
14
...
»

Summary of Contents for BVRAMB

















Reviews:

No comments

Related manuals for BVRAMB

Brand: W Audio Pages: 12

Brand: Nady Systems Pages: 12

Brand: Dickson Pages: 28

DUAL-VOX LTC-07

Brand: B&G electronics Pages: 20

Brand: SAL Pages: 21

Brand: Motorola solutions Pages: 82

Brand: Perrycom Pages: 20

Brand: Agilent Technologies Pages: 174

ProfiDAT compact

Brand: Conductrix Wampfler Pages: 32

Brand: Konix Pages: 20

LB-SV-KMIC01-V2 Series

Brand: Lab31 Pages: 73

Brand: VigaMusicTools Pages: 28

Brand: Kenwood Pages: 5

Brand: Kenwood Pages: 4

Brand: Kenwood Pages: 6

Brand: Kenwood Pages: 4

Brand: Kenwood Pages: 6

Brand: Kenwood Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands