Lift the Handset of any telephone on the PABX.
Dial the Internal extension number of the TLT 06
and wait until aconnection is built up.
Dial (*) Pin-Code (*)
Default setting ex works is:
1
2
3
*
*
*
*
*
*
*
*
*
*
*
#
#
#
#
#
#
*
*
*
#
P1
P1
P2
P2
P3
P3
P4
P4
8
8
0
0
0
1
1
1
0
Programm memory No. 1 with a telephone number
etc. up to memory No. 6 ( when used )
Programm memory No. 2 with a telephone number
Programm memory No. 3 with a telephone number
Will be dialled:
Flash (R)
Break
N1
N1
N1
N2
N2
N2
.
.
.
.
.
.
.
.
.
.
.
.
Memorizing telephone number’s
Special function keys (
)
Optional
Entrance to Programming mode
PROGRAMMING
TONE’s and SIGNALIZING
:
1
Electrical Door-opener
with
Default setting ex works
An individual ( 4 digit ) PIN-Code
Replace the handset ( on-hook )
Or
2 2 2 2
Finalize Programming
#
1
#
*
*
0
N1 N2
.
.
.
#
1
*
*
0
N1 N2
.
.
..
.
.
.
.
.
Programming
*
*
P1 P2 P3 P4
9
Changing the PIN-Code (
)
Optional
Enter new PIN-Code.
P1 - P4 are four digits from 1 - 9 via the keypad
example
“
”
“ ”
getting an external line
with
with
:
Flash
0
Occupied ( PABX ):
Extension occupied:
Hand-shake tone:
Error tone:
.... Is dependent
.... Extension occupied / busy-tone detection
.... Hand-shake tone and during Programming.
.... Signalizes a Programm error, wrong PIN-code or after 5 sec. by the use of the Star
( * ) button for fast Speech disconnection.
on the used PABX telephone system.
For programming and control function a standard
telephone with the usual 12 buttons
is necessary.
(
)
und (
) dialing
0...9, , #
MFV
*
Access to the programming mode is only possible
for authorized persons by use of a PIN -Number
(Personal Identification Number).
There are 6 memories available each of which can
memorize upto 32 digits( N1, N2...) or special signs.
The memories are assigned to the appropriate
buttons ( see connection diagramm ).
As soon as a speech connection to the TLT 06 is
built up, the electronic power switch can be
activated by dialing (
) or a
-Code.
00
PIN
For safety against unauthorized intervention, the
entrance to the programming mode is protected by
a PIN-code.
Special signs, depending on the operation can also
be memorized together with the telephone number.
The memorized telephone numbers and settings
are saved in a non volatile memory. This prevents
the loss of data by a voltage failure.
The behavior of the TLT 06 after putting the telephone on-hook can vary and is dependent on the used PABX telephone system. If the period of the
reciept tones seems to be too long, the following short-cut can help. Instead of just putting the telephone on-hook press the star (*) button of the
keypad first and then put the telephone on-hook. A reciept tone sounds as a hand shake of this and approx. 5 secs. after this 4 beep tones, then the
TLT 06 goe’s automatically offline. Normally this procedur is not necessary and the TLT 06 beeps about 3-4 times during busytone detection and
then goe’s offline without any further action.
