Maintenance and care
Cleaning waste water pump
1
2
3
CLICK!
A
B
For perfect rinsing results ...
Filters
... check,
if required,
clean.
Rotate
filter cylinder,
remove filter
system...
rinse
under
running
water ...
insert ...
Screw on
filter system
NOTE
MARK!
Spray arms
...Remove
blockages/
deposits.
pull lower arm
upwards...
unscrew
upper arm …
clean spray nozzles
under running water
(if required
use toothpicks) ...
insert
lower arm ...
screw on upper
arm tightly
– Pull out the mains plug.
– Remove filters and scoop out water.
– Lever off cover (
A
).
– Check area around the fan impeller
for foreign objects.
– Click cover shut (
B
).
– Insert filters.
Rectifying minor faults yourself ...
... as it is worth doing it yourself!
Fault
Possible causes
Remedial action
Display “
6
” is lit
Supply fitting jammed or calcified
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 10l/min.,
when water supply is open.
If the flow rate is less, replace the supply fitting.
Open supply fitting.
Install supply hose without kinks.
Waste water pump blocked
Clean waste-water pump (see above).
Rust on the cutlery
Cutlery not rust-resistant
Hard knife blades are more susceptible
Extraneous rust
Use dishwasher-proof cutlery.
Never wash rusting parts in the appliance.
Residual water
in the appliance
Appliance has technical defect
Waste water hose is blocked
or kinked
Cover not attached to waste
water pump
Call factory customer service (state fault display).
Unplug appliance.
Install waste water hose without kinks.
Attach cover (see above).
The programme has not yet ended
Fault
Possible causes
Remedial action
More information can be found in the operating instructions
Utensils are not clean
Sand or gritty residue
on the utensils
Utensils are situated close together
or one above the other
Too little detergent
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Spray arms blocked
Separate the utensils, prevent contact points.
Follow manufacturer’s instructions (detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Clean the filters (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Stains and streaks
Milky deposits
on the utensils
(can be removed)
Milky deposits, glasses
cloudy/tarnished
(cannot be removed)
Plastic/utensils
discoloured
Rinse aid dosage too high/too low
Water softening system incorrectly set
No salt
Glasses not dishwasher-proof
Too little detergent
Discoloration caused by food colourings
(tomato sauce)
Streaks: reduce dosage.
Water or limescale stains: increase dosage.
Correctly set water softening system.
Refill with special salt.
Use dishwasher-proof glasses.
Use a detergent suitable for glasses.
Follow manufacturer’s instructions (detergent).
Discoloration is harmless;
subsequent rinse cycles will cause it to fade.
Utensils not dry
Rinse aid
Increase dosage.
Change the product.
The combined detergent used
has a poor drying performance
Use rinse aid.
Appliance setting
Activate intensive drying (depending on model).
Display “
6
” flashes
Close the appliance and switch it on or terminate
the programme (see Terminating the programme).
Dishwasher-proof utensils (not soiled with ash, wax, lubricating grease, ink
or adhesive labels; remove large remnants of jam, milk products and food
according to the operating instructions and check that the spray arms can rotate freely.
While the programme is running,
press the START button
for approx. 3 sec. (Reset).
Approx. 1minute
after the programme ends,
“Programme end”
display is lit.
Switching off the appliance.
Terminating the programme ...
Loading the dishwasher correctly ...
