Maintenance and care
For perfect rinsing results ...
Cleaning waste water pump
Filters ...
check, if
required clean
Rotate filter
cylinder, remove
filter system ...
rinse under
running water ...
insert ...
Screw on filter
system NOTE
MARK!
– Pull out the mains plug
– Remove filters and scoop out water
– Lever off cover (––>A)
– Check area around the fan impeller
for foreign objects
– Click cover shut (––>B)
– Insert filters
Spray arms ...
Remove
blockages/deposits
pull lower arm
upwards ...
unscrew
upper arm ...
clean spray nozzles
under running water
(if required use
toothpicks) ...
insert lower arm ...
screw on upper arm
tightly
A
B
Rectifying minor faults yourself ...
... as it is worth doing it yourself!
Fault
Possible causes
Display “ ” display is lit
Supply fitting jammed or calcified
Open supply fitting.
Remedial action
Display “E:25”
and “ ” is lit
Waste water pump blocked
Clean waste-water pump (see above).
Rust on the cutlery
Cutlery not rust-resistant. Hard knife
blades are more susceptible
Never wash rusting parts
in the appliance.
Other fault display “E:XX”
is lit
Display “E:24”
and “ ” is lit
Residual water
in the appliance
Appliance has technical defect
Waste water hose is blocked
or kinked
Unplug appliance.
Install waste water hose without kinks.
The programme has not yet
ended
Close and switch on the appliance or
terminate the programme
(see Terminating the programme).
Cover not attached to waste
water pump
Install supply hose without kinks.
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 10 l/min. when
water supply is open. If the flow rate
is less, replace the supply fitting.
Attach cover (see above).
Call factory customer service
(state fault display).
Extraneous rust
Use dishwasher-proof cutlery.
Fault
Possible causes
Remedial action
Stains and streaks
Milky deposits on the
utensils (can be removed)
Rinse-aid dosage too high/too low
Glasses not dishwasher-proof.
Streaks: reduce dosage.
Use dishwasher-proof glasses.
Use a detergent suitable for glasses.
More information can be found in the operating instructions
Milky deposits, glasses
cloudy/tarnished
(cannot be removed)
Correctly set water softening system.
Utensils are not clean
Spray arms blocked
Clean the filters (see above).
Plastic/utensils discoloured
Too little detergent.
Follow manufacturer’s instructions
(detergent).
Sand or gritty residue on the
utensils
Utensils are situated close together or
one above the other
Too little detergent
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Separate the utensils, prevent contact
points.
Follow manufacturer’s instructions
(detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Water softening system incorrectly set;
No salt
Water or limescale stains: increase
dosage.
Refill with salt.
Discoloration caused by food colourings
(tomato sauce)
Discoloration is harmless; subsequent
rinse cycles will cause it to fade.
Terminating the programme ...
Loading the dishwasher correctly ...
While the programme is running,
press the START button for
approx. 3 sec. (Reset).
The numerical display
indicates “0:01”
Switching off the appliance
approx. 1 minute after
the programme ends,
0:00 is indicated
Dishwasher-proof utensils (not soiled with ash, wax, lubricating grease, ink or adhesive labels; remove
large remnants of jam, milk products and food according to the operating instructions and check that the
spray arms can rotate freely.
