Bailey Infi 90 IMQRS02, Instruction

Page: 26 / 48

INSTALLATION
SETUP/PHYSICAL INSTALLATION
I-E96-316A 3 - 3
Analog Output Default Switch (S2)
The analog output default switch (S2), shown in Figure 3-1 ,
determines the QRS analog output default values. These are
the values or levels for the analog outputs during system
start-up
(power up ) or bus fault error ( time-out ).
You can select either a 0 percent or 100 percent power up out-
put. Selecting 0 percent will output 4 mA or 1 VDC; selecting
100 percent will output 20 mA or 5 VDC. Switch position 3
selects the value for Analog Output 1 (AO1) and position 6
selects the value for Analog Output 2 (AO2). S3 determines the
mode of the output (current or voltage).
If the bus fault timer expires (time-out ), the digital outputs
de-energize and the analog outputs change to the default value
selected. A
time-out occurs when the slave does not receive a
clock signal from the MFP. The time-out options are to hold or go
to power up state . The outputs stay at their current values dur-
Table 3-1. Address Switch Settings (S1)
Addr
MSB LSB
Addr
MSB LSB
3 4 5 6 7 8 3 4 5 6 7 8
0 0 0 0 0 0 0 32 1 0 0 0 0 0
1 0 0 0 0 0 1 33 1 0 0 0 0 1
2 0 0 0 0 1 0 34 1 0 0 0 1 0
3 0 0 0 0 1 1 35 1 0 0 0 1 1
4 0 0 0 1 0 0 36 1 0 0 1 0 0
5 0 0 0 1 0 1 37 1 0 0 1 0 1
6 0 0 0 1 1 0 38 1 0 0 1 1 0
7 0 0 0 1 1 1 39 1 0 0 1 1 1
8 0 0 1 0 0 0 40 1 0 1 0 0 0
9 0 0 1 0 0 1 41 1 0 1 0 0 1
10 0 0 1 0 1 0 42 1 0 1 0 1 0
11 0 0 1 0 1 1 43 1 0 1 0 1 1
12 0 0 1 1 0 0 44 1 0 1 1 0 0
13 0 0 1 1 0 1 45 1 0 1 1 0 1
14 0 0 1 1 1 0 46 1 0 1 1 1 0
15 0 0 1 1 1 1 47 1 0 1 1 1 1
16 0 1 0 0 0 0 48 1 1 0 0 0 0
17 0 1 0 0 0 1 49 1 1 0 0 0 1
18 0 1 0 0 1 0 50 1 1 0 0 1 0
19 0 1 0 0 1 1 51 1 1 0 0 1 1
20 0 1 0 1 0 0 52 1 1 0 1 0 0
21 0 1 0 1 0 1 53 1 1 0 1 0 1
22 0 1 0 1 1 0 54 1 1 0 1 1 0
23 0 1 0 1 1 1 55 1 1 0 1 1 1
24 0 1 1 0 0 0 56 1 1 1 0 0 0
25 0 1 1 0 0 1 57 1 1 1 0 0 1
26 0 1 1 0 1 0 58 1 1 1 0 1 0
27 0 1 1 0 1 1 59 1 1 1 0 1 1
28 0 1 1 1 0 0 60 1 1 1 1 0 0
29 0 1 1 1 0 1 61 1 1 1 1 0 1
30 0 1 1 1 1 0 62 1 1 1 1 1 0
31 0 1 1 1 1 1 63 1 1 1 1 1 1
1= OPEN ; 0=CLOSED