background image

 

 
 

 

1.0 Important Safety Instructions 

When using an electrical appliance, basic precautions should always be followed, including the following: 

READ ALL INSTRUCTIONS BEFORE USING THIS AIR FILTRATION UNIT. 

 To reduce the risk of fire, electric shock, or injury: 

1.  Read and understand the entire owner's manual before attempting assembly or operation. 

2.  Read  and  understand  the  warnings  posted  on  the  machine  and  in  this  manual.  Failure  to  comply  with  all  of  these 

warnings may cause serious injury. 

3.  Replace the warning labels if they become obscured or removed. 

4.  Do not use this air filtration system for other than its intended use. If used for other purposes, 

Baileigh disclaims any 

real or implied warranty and holds itself harmless from any injury that may result from that use. 

5.  Never duct a machine directly into the air filtration unit. 

6.  To avoid a potentially dangerous situation, do not use this equipment to filter volatile fumes or smoke. 

7.  Do not use this equipment to filter flammable vapors. This air filtration unit is designed and intended for the filtration of 

air borne dust only. It is neither designed nor intended for any other purpose whatsoever. 

8.  Keep visitors a safe distance from the work area. Keep children away. 

9.  Make your workshop child proof with padlocks, master switches or by removing starter keys. 

10. 

DRUGS, ALCOHOL, MEDICATION.

  Do not operate tool while under the influence of drugs, alcohol or any medication. 

11.  Make certain the switch is in the OFF position before connecting the machine to the power supply. 

12.  Make certain the machine is properly grounded. 

13.  Use recommended accessories; improper accessories may be hazardous. 

14. 

GROUND  ALL  TOOLS.   

If  tool  is  equipped  with  three  prong  plug,  it  should  be  plugged  into  a  three-hole  electrical 

receptacle. If an adapter is used to accommodate a two-prong receptacle, the adapter lug must be attached to a known 
ground. Never remove the third prong. 

15. 

WARNING

: Drilling, sawing, sanding or machining wood products generates wood dust and other substances known 

to the State of California to cause cancer. Avoid inhaling dust generated from wood products or use a dust mask or 
other safeguards to avoid inhaling dust generated from wood products. Wood products emit chemicals known to the 
State  of  California  to  cause  birth  defects  or  other  reproductive  harm.  (California  Health  and  Safety  Code  Section 
25249.6) 

16.  Keep safety guards, panels, and doors in place, secured, and always closed when the machine is in use. If removed 

for  maintenance  purposes,  use  extreme  caution  and  replace  the  guards,  install  the  panels  and  close  the  doors 
immediately after completion of maintenance. 

17.  Maintain tools with care. Keep filters clean for the best and safest performance. 

18.  Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris 

 do not use your 

hands. 

19.  Do not use this air filtration unit with a damaged cord or plug. If the unit is not working as it should, has been dropped, 

damaged, left outdoors, or dropped into water, return it to a service center. 

20.  When ceiling mounted, bottom of filtration unit must be at least 7 feet from the floor. The mounts must be anchored to 

building structure which will support the weight of the air filtration unit. Never mount to surfaces such as dry wall or 
false ceiling grids. 

21.  When bench top mounted, do not place this unit on an unstable surface, or where there is a risk of tipping over. Serious 

injury could occur if the unit tips over. 

Summary of Contents for ISF-1000

































Reviews: