LIMITED LIFETIME WARRANTY
Bad Cat Amplifiers warrantees our amps and cabs against workmanship or defect for
life. The warrantee does not cover tubes or cosmetic damage, or wear and tear or abuse.
This warrantee is transferable. Modifying or altering the amp in any way voids the
warrantee. Shipping to and from the warranty repair center is the responsibility of the
customer.
We have a new Lifetime Warranty on all new amps leaving the factory. We are extending
the Lifetime Warranty to all of our pre acquisition amps for $195. Simply send the unit
back to us and we will have one our technicians go through it from the ground up. And to
top it all off, we will pay for the shipping back to you. For more information please contact
us at [email protected] or directly at 714-630-0101
When RETURNING merchandise to the factory, you must call for a return authorization
number.
HELP SECTION
1) AMP WILL NOT TURN ON
Check the power to the amp. Check for tripped circuit breakers, unplugged extension
cords or power-strip switches that may be turned off. Check the fuse. If a dark brownish
color or no wire can be seen within the glass tube, then replace. The amp may be perfectly
fine but occasionally a fuse may blow because of high AC voltage surges. After the fuse
has been replaced with the proper Slow Blow value and if the fuse fails again, the amp
will require servicing.
2) NO OUTPUT with POWER light ON
Tubes damaged in shipping will be the primary reason for your amp to not function
properly. Please give us a call to help guide you through this simple repair.
3) KEEP YOUR AMP LOOKING NEW
Use a damp cloth to wipe the controls on the front & rear chassis panels. Wipe the black
vinyl covering with a damp cloth.
IMPORTANT!
FOR YOUR PROTECTION, PLEASE READ
THE FOLLOWING:
WATER AND MOISTURE: Appliance should
not be used near water (near a bathtub,
washbowl, kitchen sink, laundry tub, in a
wet basement, or near a swimming pool,
etc). Care should be taken so that objects
do not fall and liquids are not spilled into
the enclosure through openings.
POWER SOURCES: The appliance should
be connected to a power supply only of
the type described in the operating in-
structions or as marked on the unit.
GROUNDING OR POLARIZATION: Precau-
tions should be taken so that the ground-
ing or polarization means of an appliance
is not defeated.
POWER CORD PROTECTION: Power sup-
ply cords should be routed so that they
are not likely to be walked on or pinched
by items placed upon or against them,
paying particular attention to cords at
plugs, convenience receptacles, and the
point where they exit from the appliance.
SERVICING: The user should not attempt
to service the unit beyond that described
in the operating instructions. All other
servicing should be referred to qualified
service personnel.
FUSING: If your unit is equipped with a
fuse receptacle, replace only with the
same type fuse. Refer to replacement
text on the unit for correct fuse type.
This symbol is intended to alert
the user to the presence of
uninsulated
“dangerous
voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute
a risk of electric shock to persons.
This symbol is intended to
alert the user to the presence
of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL!
THIS UNIT CONTAINS HIGH VOLTAGE INSIDE!
PHONE 714.630.0101
FAX 714.630.0106
WWW.BADCATAMPS.COM
5 TECHNOLOGY DRIVE IRVINE CA 92618
BAD CAT HOLDINGS LLC. USA
Operation
The Leash is easy to use. Just follow these simple steps for years of trouble-free service. Your equipment should be “OFF” while connecting. Plug your
amplifier into the jack marked “AMP” and your speaker into the jack marked “SPEAKER”. Now, turn on your amplifier. The In/Out switch is true-bypass.
There is a small amount of insertion loss when switching the device “In” (typically1db). Set the Ohms selector to match the output impedance of your
amplifier and the Ohms rating of your speaker. Using a mismatched load will result in degraded performance. For best results in any case, always match
the Ohms selector to the amplifier. To help with Ohms calculation, the two speaker jacks are wired in parallel (for use with additional cabinets). The
large knob on the front controls your overall balance between speaker load, from whisper quiet to maximum loudness. The Leash dissipates unused
audio power by converting it to heat. An AC power cord operates a cooling fan located at the top of the housing. This fan allows The Leash to operate at
maximum efficiency under all playing conditions. To prevent damage to The Leash or your amplifier, it is absolutely essential that the onboard cooling
fan be operating whenever The Leash is in use.
All manuals and user guides at all-guides.com
