background image

7

LEVEL AND SQUARE FLOOR FRAME

Before attaching fl oor decking, it is important to level and square the fl oor frame.

A level and square fl oor frame is required to correctly construct your shed.

First, secure at ends with one fastener.

Second, secure at ends with one fastener.

Fig. A

FINISH

BEGIN

2

3

4

1

Use level and check the frame is level before applying fl oor panels.

Check for frame squareness by measuring diagonally across corners. 
If the measurements are the same, the frame is square. 
The diagonal measurement  will be approximately 151-1/2" (384,8 cm).

When the frame is level and square secure one side of frame to the 4x4 runners with one fastener 

at ends of each runner. 
Move to the opposite end of the frame. Secure the frame to 4x4 runners with one fastener at ends

of each runner making sure the frame remains square 

(Fig. A)

.

Once the fl oor frame is level and square, fasten the frame to the 4x4 runners at each connection.

      See page 10 for the preferred fl oor leveling method.

151-1/2" 

(384,8 cm)

151-1/2" 

(384,8 cm)

Summary of Contents for Handy Home Products KENNESAW
























































Reviews: