BBW03-GS-IM-120630
C.
Instruction for Use
i.
Preparing baby food
It can be warmed all kinds of feeding bottles as well as baby food jars and tins safely and
quickly. But it is not suitable to keep liquid or food warm as vitamins may be destroyed.
The time to heat up the milk or food depends on the size of the bottle and the temperature
of the milk or food (e.g. room temperature 20˚C or out of fridge 5˚C). The following table
shows the approximate warming time for different situations:
Table 2
Heating Setting
Initial food temperature
Volume
Setting
20
℃
5
℃
125ml(4oz) bottle
Low
4 mins
5 mins
260ml(9oz) bottle
Low
5 mins
7 mins
330ml(11oz) bottle
Low
6 mins
8 mins
130g food jar
Low
5 mins
7 mins
190g food jar
Low
7 mins
9 mins
For feeding bottles:
1). Place the insulation spacer, assembled and filled feeding bottle in the warmer.
2). Close the bottle cover tightly.
3). For 125ml/4oz feed bottle, fill the warmer with water to just above the level of milk in the bottle.
For larger bottles (260ml/9oz), fill the warmer to 15mm below the rim of the warmer.
4).
Note: Never put the water level over the neck of the bottle or spill over the edge of the
warmer.
5). The heater can be covered or left it opens.
6).
Plug in and press the “
warm
” button to start the operation.
7). During the heating process, the indication light stays ON. When the temperature reaches the
preset value, it changes to keep warm mode.
8). Caution: Milk should not be overheated. Take it out when reaches the preset temperature.
9). Caution: Shake the bottle gently and check its temperature by sprinkling a few drops on to
your hand before feeding.
CAUTION:
THE WATER INSIDE THE STEAMER MAY BE HOT!
BE CAUTION WHEN REMOVING ANY BOTTLE AFTER COMPLETION.
For baby food jars and tins:
1). Put the insulation spacer in the heater.
2). Remove the lid and place jar or tin in the heater.
3). Fill the heater with water to 15mm (1/2 inch) below the top of the jar/tin.
4). The heater can be covered or left it opens.
5).
Plug in and press the “
warm
”
button to start the operation.
6). During the heating process, the indication light stays ON. When the temperature reaches the
preset value, it changes to keep warm mode.
7). Caution: Baby food should not be overheated. Take it out when reaches the preset
temperature.
8). Caution: Stir the food and check its temperature to ensure it is suitable for feeding.
Caution: Beware the hot water around the bottle or jars when taking out after heating process.
Caution: For bottle warming or baby food heating, please refer to the timetable in Table 2.
CAUTION:
THE WATER INSIDE THE STEAMER MAY BE HOT!
BE CAUTION WHEN REMOVING ANY FOOD JAR, FEEDING BOWL, OR ACCESSORIES AFTER
COMPLETION.
ii.
Bottle Sterilization
1)
Put the insulation spacer in the heater.
2)
Add approximate 80ml water to the heater.
3)
Put the bottle upside down into the steamer and then closed it by the steamer cover.
4)
Plug in the unit and press the
“
steam
” button to start the operation.
5)
Warning: Steam will be come out during the sterilization process. Keep clear from the
steam to avoid injury.
6)
Warning: The steamer surface is hot during the sterilization process. Please handle with
care.
7)
During sterilization process, the indication light stays ON. It takes about 10 minutes, press
“
” when necessary.
Note: You can press
“
” anytime to stop the sterilization process.
8)
When all water in the heater is evaporated, the appliance will turn to protective mode, unless
water is added.
9)
Please do not open the steamer cover right after the sterilization process, open the cover 4~5
minutes after its cool down.
